background image

FTII-IOM-8

82-0253

Finned copper tube

Gas boilers (FB) & 

Water heaters (FW)

Copyright 2010 Mestek, Inc.

260 North Elm Street  

7555 Tranmere Drive

Westfi eld, MA 01085   

Mississauga, ONT. L5S IL4 Canada

Tel:   (413) 568-9571  

Tel:   (905) 670-5888

Fax:  (413) 568-9613    

Fax:  (905) 670-5782         

                    www.rbiwaterheaters.com

  Th is manual is intended only for use by a qualifi ed heating installer/technician. Read and follow this manual, all supplements and related 

instructional information provided with the boiler. Install, start and service the boiler only in the sequence and methods given in these 
instructions. Failure to do so can result in severe personal injury, death or substantial property damage.

 

Do not use the boiler during construction.

 Construction dust and particulate, particularly drywall dust, will cause contamination of 

the burner, resulting in possible severe personal injury, death or substantial property damage.  Th e boiler can only be operated with a dust-
free air supply. Follow the instruction manual procedures to duct air to the boiler air intake. If the boiler has been contaminated by operation 
with contaminated air, follow the instruction manual guidelines to clean, repair or replace the boiler if necessary.

 Affi  x these instructions near to the boiler/water heater. Instruct the building owner to retain the instructions for future use by a qualifi ed 

service technician, and to follow all guidelines in the User’s Information Manual.

Boiler manual

Installation and

operation instructions

Summary of Contents for FUTERA II Series

















































Reviews: