![background image](http://html1.mh-extra.com/html/radio-shack/lab-1200/lab-1200_specifications_3422341001.webp)
Fully-Automatic
Belt Drive Turntable
with Pre-Amp
42-7012
Note: The LIN (lead in), RET (auto return),
and SW (tone arm switch) screws on the
bottom of the turntable are set at the factory
and should not be adjusted.
1.
Open the dust cover.
2.
Rotate the turntable’s platter until one of
the platter’s two larger holes is above
the drive motor spindle on the
turntable’s upper left side.
3.
Remove the tape and two ribbons from
the rubber drive belt. Be sure the belt is
not twisted.
4.
Using your fingers, securely seat the
belt on the center of the drive motor’s
spindle (against the lower rim).
5.
Plug the turntable’s power cord into a
standard AC outlet.
6.
Remove the wire tie from the tone arm,
then press CUE to raise the tone arm.
7.
Press PLAY and let the motor rotate the
turntable six or seven times, then press
STOP and check the location of the belt
on the spindle. If the belt is not securely
seated around the spindle, reposition it
properly and repeat Step 6.
Note: If the belt slips off the spindle, do not
attempt to remove the platter. Take it to your
local RadioShack store for assistance.
8.
Unplug the turntable’s power cord from
the AC outlet.
9.
Connect the turntable’s ground wire to
the amplifier’s/receiver’s GND or earth
terminal to avoid hum.
10. Place the rubber mat, ridged side down,
on top of the platter.
Assemble Your Turntable
Thank you for buying the RadioShack LAB-1200 Fully-Automatic
Belt Drive Turntable. This is a high quality stereo turntable with
sensitive pickup and a built-in pre-amp that delivers great sound
from your records.
Tone arm
Dust cover
Rubber mat
45 RPM adapter
PLAY
STOP
CUE
Connect Your Turntable
Connecting Your Turntable to a Receiver/Amplifier
You can connect your LAB-1100 to a receiver/amplifier (or stereo audio
mixer) that has low-level phono inputs (such as left and right PHONO
jacks) or line-level inputs (such as left and right AUX, TV, TAPE, or CD
jacks).
Cautions:
• Do not connect the turntable to AC power until you complete all other
connections.
• Do not place the turntable on top of the receiver/amplifier or on any
other component that gets hot.
• To avoid possible damage to your receiver/amplifier, turn it off before
making the connections
.
Note: If you are not sure which type of input your receiver/amplifier has,
check your receiver’s/amplifier’s owner’s manual.
Low Level Inputs
To connect the turntable to a low-level phono input, plug the white
and red plugs into the receiver’s/amplifier’s left and right PHONO
jacks. Then set LINE OUT ON/PHONO OUT OFF to
PHONO OUT OFF.
Line Level Input
s
To connect the turntable to a line-level input, plug the white and red
plugs into the receiver’s/amplifier’s left and
right AUX, TV, TAPE, or CD jacks. Then set
LINE OUT ON/PHONO OUT OFF to LINE
OUT ON.
Connecting to Power
Once you have connected the turntable to your
receiver/amplifier, plug the turntable’s power
cord into an AC outlet on your receiver/amplifier
or into a standard AC outlet.
Caution: To prevent electric shock, the plug’s blades are polarized and
fit only one way. If the plug does not fit easily, turn it over and try again.
Note: Depending on if your sound system has
PHONO jacks or not, be sure to set
LINE OUT ON/ PHONO OUT OFF as described in
“Connect Your Turntable”.
1.
Open the dust cover.
2.
Remove the stylus cover.
3.
If you are playing a 33
1
/
3
RPM record, place it
directly over the spindle. If you are playing a 45
RPM record, place the supplied 45 RPM
adapter over the turntable spindle, then place
the record over the adapter.
4.
Press SPEED in or out to set the turntable’s
speed (33
1
/
3
or 45 RPM).
5.
Press PLAY. The turntable starts to rotate and
the tone arm moves to the beginning of the
record, lowers to the record, then starts to play.
6.
At the end of the record, the tone arm
automatically returns to the tone arm rest and
the turntable stops. To stop playing the record
sooner, press STOP. If the tone arm does not
automatically return when it reaches the end of
the record, press STOP to reset the
mechanism.
Using The Cue Button
1.
Press CUE to raise the tone arm.
2.
Push the tone arm to a spot directly over the
desired part of the record. The turntable starts
to rotate.
3.
Press CUE again. The tone arm slowly lowers
and the record plays.
Use Your Turntable
The lightning symbol is intended to alert you to the presence of
uninsulated dangerous voltage within this product’s enclosure
that might be of sufficient magnitude to constitute a risk of
electric shock. Do not open the product’s case.
The exclamation symbol is intended to inform you that
important operating and maintenance instructions are
included in the literature accompanying this product.
WARNING:
To reduce the risk of fire or shock hazard, do not
expose this product to rain or moisture.
CAUTION
CAUTION:
TO REDUCE THE
RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER OR
BACK. NO USER-
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO
QUALIFIED PERSONNEL.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
!
!
Rear View
SPEED
Phono Plugs
Ground Cable
Power Cord
Stylus cover
©2004 RadioShack Corporation
42-7012
All Rights Reserved.
Printed in China
RadioShack and RadioShack.com are trademarks
04A04
used by RadioShack Corporation.
What’s Included
User’s Guide - Turntable
Rubber Turntable Mat - 45 RPM adapter
42-7012.fm Page 1 Thursday, April 22, 2004 1:38 PM