TM
2
3
4
5
6
7
We hope you enjoy your Wireless Weather
Station from RadioShack. This weather
station features a clock with alarm function,
and minimum and maximum indoor/outdoor
temperature display. It works with up to three
sensors (additional sensors not included). Please
read this user’s guide before using your new
weather station.
Package Contents
•
Weather Station
•
Thermo Sensor
•
User’s Guide
Specifications
Indoor Temperature Range ... 32–122°F (0–50°C)
Outdoor Temperature Range ....................................
.................................................. -4 – 140°F (-20–60°C)
Sensor RF Frequency ..................................433 MHz
RF Operation Range ...............................98 ft (30 m)
Channel Number .........................................................3
Specifications are subject to change and improvement
without notice. Actual product may vary from the
images found in this document.
Wireless Weather Station
6301469
User’s Guide
Set Weather Station and Sensor
1.
Place the weather station and sensor close
together indoors to communicate.
2.
Slide the sensor’s
CH 1 2 3
switch to select a channel,
and press the weather
station’s
CH +
button to
select the same channel. If
you are using more than one
sensor (up to three), select
a different channel for each
sensor.
high enough where it is out of reach for
children. The sensor should be mounted
onto a vertical flat surface. Avoid location
where rain and water falls directly onto the
sensor.
Install Batteries
1.
Insert two AA batteries (not included) into
the weather station and thermo sensor
respectively, matching the polarity symbols
(
+
and
–
) marked inside each battery
compartment.
2.
Press
RESET
on both units.
Battery Note:
•
Dispose of old batteries promptly and
properly. Do not burn or bury them.
•
Use only a fresh battery of the required size
and type.
•
Use alkaline batteries for longer usage, or
use lithium batteries in temperatures below
-4°F (-20°C).
•
Do not mix old and new batteries, or
batteries of different types, capacities, or
chemistries.
Weather Station
Thermo Sensor
AA
AA
AA
AA
RESET
CH 1 2 3
SNOOZE / LIGHT
•
Silence the alarm for
5 minutes when the
alarm sounds.
•
Turn the backlight on.
ALARM SET
•
Enter and
confirm alarm
settings.
•
View the set
alarm time.
• Activate the
alarm.
CH +
•
Set the hour
and minute.
•
Select a sensor.
MEM –
•
Set the hour
and minute.
•
View maximum
(
MAX
), minimum
(
MIN
) or current
indoor/outdoor
temperature.
DISPLAY SET
Enter and confirm
clock settings.
°C/°F
Change between
Celsius and Fahrenheit.
SENSOR
Scan sensor signal.
RESET
Clear all indoor/outdoor
temperature data,
and clock and alarm
settings.
Important Installation and
Location Notes
•
During initial installation, the sensor may
take up to an hour or more to acclimate to
current conditions.
•
Place the weather station indoors away from
vents, heating or cooling elements, and
direct sunlight.
•
Stand the sensor on
a flat surface indoors
or outdoors away
from direct sunlight
and moisture. Or use
a screw (not included)
to mount it on a wall.
Make sure the sensor is within 98 feet (30m)
of the weather station, without obstructions
between them.
To avoid interference, place
the weather station and sensor away from
other electronic devices.
•
If the sensor is placed outdoors, mount it
high enough off the ground where water,
snow, and rain cannot accumulate and also
•
If you do not plan to use your weather
station for more than a month, remove the
batteries. Batteries can leak chemicals that
can damage electronic parts.
3.
Press the weather
station’s
SENSOR
button to scan sensor
signal. Scanning may
take some time.
Note:
If the weather
station does not connect
to the sensor, relocate
the sensor and/or the
weather station until
connection is established.
6301469_PM_EN_081115.indd 1-7
8/11/2015 3:57:34 PM
