Quicksilver 8M920078R Owner'S Manual Download

Page: 1 / 15

- 1 -

Contents

INTRODUCTION………………...………………………………..4/184

INFLATION/DEFLATION………………………………………...4/184

FITTING OARS AND PADDLES…………………………………5/184

FITTING FIBERGLASS SEAT……………………………………6/184

DRAIN PLUG……………………………………………………...6/184

MOUNTING ENGINE……………………………………………..7/184

FITTING CONSOLES AND SEATS……………………………...7/184

FITTING OF THE STEERING SYSTEM…………………………8/184

FITTING OF THE BATTERY……………………………….…….8/184

10.

FITTING OF FUEL TANKS……………………………………….9/184

11.

NAVIGATION……………………………………………………..10/184

12.

DAVITS…………………………………………………………….11/184

13.

DEFLATION AND STOWAGE…………………………………...11/184

14.

CLEANING AND MAINTENANCE……………………………..12/184

15.

REPAIRS…………………………………………………………..12/184

16.

SAFETY RECOMMENDATIONS………………………………..13/184

17.

ENVIRONMENTAL CONSIDERATIONS……………………….14/184

18.

GUARANTEE……………………………………………………..15/184

8M920078R

Summary of Contents for 8M920078R
















Search results

Summary of Contents for 8M920078R

Reviews:

Related manuals for 8M920078R

Brands by name

Popular brands

Quicksilver 8M920078R, Owner'S Manual

Search results

Summary of Contents for 8M920078R

Reviews:

Related manuals for 8M920078R

Brands by name

Popular brands