Quark-Elec QK-W017 Application Note Download

Page: 1 / 22

Quark-Elec application note

https://www.quark-elec.com

1 of 22

2015

V1.1

QK-W017 WiFi Remote Control Gateway

— WiFi temperature/humidity data logger & remote controller

Features



Control and store heating/cooling settings for up to five individual zones



Turn electronic devices ON/OFF from any location via the Internet



Monitor environmental temperatures using a mobile phone or tablet



Output relays can be triggered manually or tied to specific temperature ranges



Standard 802.11b/g/n WiFi, easily connected to an existing wireless Access Point



Android and iOS APPs



Rapid installation and setup



Automotive temperature range (-40°C to +105°C)



± 0.5°C temperature tolerance



1% to 99.9% humidity range with down to 3% tolerance



Industrial level design



Supports both Ad-hoc and station modes on WiFi

Summary of Contents for QK-W017























Search results

Summary of Contents for QK-W017

Reviews:

Related manuals for QK-W017

Brands by name

Popular brands

Quark-Elec QK-W017, Application Note

Search results

Summary of Contents for QK-W017

Reviews:

Related manuals for QK-W017

Brands by name

Popular brands