background image

www.quadrafi re.com

7022-122D

May 12, 2014

CASTILE PELLET INSERT

O-T L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

Owner’s Manual

Installation and Operation

CASTILEI-MBK
CASTILEI-PMH
CASTILEI-CSB
CASTILEI-CWL

Model: 

SAVE THESE INSTRUCTIONS

NOTICE

•  Important operating and 

maintenance instruc-
tions included.

• 

Leave this manual with 
party responsible for use 
and operation.

• 

Read, understand and 
follow these instruc-
tions for safe installa-
tion and operation.

$/./

4

$)3#!2$

 WARNING

Please read this entire manual 
before installation and use of this 
pellet fuel-burning room heater.  
Failure to follow these instructions 
could result in property damage, 
bodily injury or even death.

• 

Do not store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this 
or any other appliance.

•  Do not overfi re - If any external part starts to 

glow, you are overfi ring. Reduce feed rate.  
Overfi ring will void your warranty.

•  Comply with all minimum clearances to com-

bustibles as specifi ed.  Failure to comply may 
cause house fi re.

Check building codes prior to installation.
•  Installation MUST comply with local, regional, state and national 

codes and regulations.

•  Contact local building or fi re  offi cials about restrictions and 

installation inspection requirements in your area.

CAUTION

Tested and approved for wood pellets and shelled 
fi eld corn fuel only.  Burning of any other type of fuel 
voids your warranty.

CAUTION

WARNING

Hot glass will cause burns.

•  Do not touch glass until it is cooled
•  NEVER allow children to touch glass
•  Keep children away
•  CAREFULLY SUPERVISE children in same room as 

fi replace.

•  Alert children and adults to hazards of high 

temperatures.

 

High temperatures may ignite clothing or other 
fl ammable materials.

• 

Keep clothing, furniture, draperies and other fl ammable 
materials away.

HOT SURFACES!

Glass and other surfaces are 
hot during operation AND 
cool down.

To obtain a French translation of this manual, please 
contact your dealer or visit www.quadrafi re.com

Pour obtenir une traduction française de ce manuel, 
s’il vous plaît contacter votre revendeur ou visitez 
www.quadrafi re.com

NOTE

Summary of Contents for CASTILEI-MBK

























































Reviews: