background image

 1 

 

 

 

 

                        7038-206F 

 

 

 

 September 27, 2016

5700 STEP TOP WOOD STOVE SERIES

Automatic Combustion Control (ACC)

Model(s): 

57ST-ACC-B

 

 

HOT SURFACES!

 

 

Glass and other surfaces are hot 

 

 

during operation AND cool down.  

Hot glass will cause burns.

• 

Do not touch glass until it is cooled

• 

NEVER allow children to touch glass

• 

Keep children away

• 

CAREFULLY SUPERVISE children in same room as 

appliance.

• 

Alert children and adults to hazards of high temperatures

•  High temperatures may ignite clothing or other 

flammable materials.

• 

Keep clothing, furniture, draperies and other flammable 

materials away.

 WARNING

If the information in these instruc-

tions is not followed exactly, a 

fire could result causing property 

damage, personal injury, or death.

 

•  Do not store or use gasoline or other flam

-

mable vapors and liquids in the vicinity of 

this or any other appliance.

•  Do not over fire - If appliance or chimney 

connector glows, you are over firing. Over 

firing will void your warranty.

•  Comply with all minimum clearances to 

combustibles as specified.  Failure to 

comply may cause a house fire.

WARNING

WARNING

Fire Risk.

For use with solid wood fuel only.

Other fuels may over fire and generate 

poisonous gases (i.e. carbon monoxide).

Installation Manual

Installation & Appliance Set-Up

INSTALLER: Leave this manual with party responsible for use and operation. 

OWNER: Retain this manual for future reference. 

NOTICE: DO NOT DISCARD THIS MANUAL

NOTE

To obtain a French translation of this manual, please contact 

your dealer or visit www.quadrafire.com

Pour obtenir une traduction française de ce manuel, s’il vous 

plaît contacter votre revendeur ou visitez www.quadrafire.com

O-T  L

Tested and 

Listed by

Portland

Oregon USA

OMNI-Test Laboratories, Inc.

C

US

Installation  and  service  of  this 

appliance should be performed by 

quali ed personnel. Hearth & Home 

Technologies  recommends  HHT 

Factory  Trained  or  NFI  certified 

professionals.

Summary of Contents for 57ST-ACC-B





























Reviews: