1. Charge the PRYMEBLU Wireless PTT
2. Pair the PRYMEBLU Adapter with a wireless headset
3. Pair the PRYMEBLU PTT with the PRYMEBLU Adapter
4. Test and Use.
3
4
QUICKSTART
1
Controls and Connection
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired
operation.
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. To maintain compliance with FCC RF exposure compliance
requirements, please avoid direct contact to the transmitting antenna during transmitting.
RF Exposure Warning!
Please keep product 20cm away from your
body or bystander during the radio operation.
The typical handheld two-way radios were
certified under mobile usage condition
(i.e. keep 20cm away from the user body)
and use of such radio closer than 20cm may
exceed the US RF exposure limit
and shall be avoided.
version 1.0 December 2010
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: 714.257.0600
TOLL FREE: 800.666.2654
WWW.PRYME.COM
PRYMEBLU
®
PUSH-TO-TALK USER’S GUIDE
For use with PRYMEBLU wireless Bluetooth Adapters (Sold Separately)
PRYME® and PRYME BLU™ are trademarks owned by PRYME Radio Products,
Brea CA. All other product or service names are the property of their respective owners.
© 2010 PRYME Radio Products, Brea CA. All Rights Reserved
This manual applies to the PRYMEBLU BT-PTT Wireless Push-to-Talk transmitter.
The PRYMEBLU PTT works with all PRYMEBLU BT-500 series Bluetooth Adapters.
STEP ONE: Charging the PRYMEBLU PTT
The PRYMEBLU PTT has an internal Lithium Ion rechargeable battery pack which must be charged prior
to operation, and must be recharged regularly. A fully charged battery will provide approximately 12
hours (or more) of operation before needing to be recharged.
To charge the PRYMEBLU PTT:
* Ensure the PRYMEBLU PTT is turned off, using the switch located on the back of the device.
* Plug the supplied wall charger into an AC (110V) wall outlet.
* Plug the charger into charge jack on the bottom of the PRYMEBLU Adapter. You will need to remove
the protective rubber cover that is inserted into the charge jack. (To prevent dust and moisture from
damaging your PTT, always ensure this cover is in place when you are not charging the PRYMEBLU PTT.)
* The PRYMEBLU PTT takes approximately 4.5 hours to charge. Actual charge time will vary depending
on several factors including the battery’s charge state, condition, and age.
Charging Cautions:
- Use only the wall charger supplied by the manufacturer. Do not use any other charger.
- Do not use a wall charger that appears to be damaged. (Example: frayed wires, melted plastic, etc.)
Contact PRYME to get a new manufacturer-approved replacement charger.
- Do not tamper with or modify the PRYMEBLU PTT or charger.
-Always turn the power switch to the Off position when charging the PRYMEBLU PTT.
USING THE FRICTION PAD
The PRYMEBLU PTT is supplied with a rubber Friction Pad. This pad provides additional protection and
stability when using the Velcro Fastener on the back of the PRYMEBLU PTT to attach the device to an
automobile steering wheel, gearshift, or any other location.
To install the rubber Friction Pad do the following:
1. Open the Velcro Fastener on the back of the
PRYMEBLU PTT so that the two straps are separated.
2. Align the Friction Pad so that it is centered over the
Velcro Fastener on the back of the PRYMEBLU PTT.
3. Slide one strap of the Velcro Fastener into one
of the slots in the Friction Pad and pull the strap through.
4. Slide the other Velcro Fastener strap through the other slot in the Friction Pad.
5. Place the PRYMEBLU PTT in the position you wish to mount it and close the Velcro Fastener.
Push-To-Talk Button
When paired with a PRYMEBLU Adapter
and wireless headset, this button functions
as a Push-to-Talk, causing the two-way radio
to transmit when the switch is pressed.
LED Indicator
The LED flashes messages that let
the user know the current status of
the PRYMEBLU PTT.
Charge Jack
This jack is used to connect the
PRYMEBLU PTT to the supplied
wall charger.
Lanyard Attachment Point
Allows attachment of a wrist strap
or lanyard to the PRYMEBLU PTT.
Velcro Fastener
The Velcro strap on the back of the
PRYMEBLU PTT rotates 360° and allows
the PRYMEBLU PTT to be securely attached
in many convenient locations, such as to
the user’s clothing, around the user’s fingers,
on an automobile steering wheel, on duty
gear, and many more!
Power Switch
Turns the
PRYMEBLU PTT
on and off.
The PRYMEBLU PTT allows you to Push-to-Talk wirelessly over your two-way radio when using
with a PRYMEBLU Adapter and a compatible wireless headset.
PRYMEBLU PTT
Model No.: BT-PTT
Made in Taiwan
FCC ID N2E-BT-PTT
