Prusa Research MINI+ Manual Download

Page: 1 / 32

Table of Contents

Manual changelog MINI+ semi-assembly

................................................................

Step 1 - Version history

.................................................................................................

Building your MINI+

...........................................................................................................

Step 1 - Preassembled vs kit version

...........................................................................

Step 2 - Different hardware revisions

.........................................................................

Step 3 - All the required tools are included

...............................................................

Step 4 - Use labels for reference

.................................................................................

Step 5 - We are here for you!

........................................................................................

Step 6 - XYZ-axes parts preparation

..........................................................................

Step 7 - XYZ-axes parts preparation

...........................................................................

Step 8 - Foam pads - preparation

...............................................................................

Step 9 - Foam pads installation

...................................................................................

Step 10 - Opening the box with the electronics

......................................................

Step 11 - Connecting the LCD cable

..........................................................................

Step 12 - Connecting the Y and XZ-axis assembly

.................................................

Step 13 - Joining the parts together - preparation

..................................................

Step 14 - Protecting the LCD cable

...........................................................................

Step 15 - Joining the parts together - phase 1

..........................................................

Step 16 - Joining the parts together - phase 2

.........................................................

Step 17 - Joining the parts together - phase 3

.........................................................

Step 18 - Aligning the XZ-axis assembly

..................................................................

Step 19 - Final tightening

............................................................................................

Step 20 - Haribo time!

.................................................................................................

Step 21 - LCD parts preparation

................................................................................

Step 22 - Mounting the LCD

.......................................................................................

Step 23 - Connecting the LCD

...................................................................................

Step 24 - Guiding the LCD cable

...............................................................................

Step 25 - Connecting the Y-axis motor

....................................................................

Step 26 - Connecting the heatbed cable

..................................................................

Step 27 - Filament sensor (optional)

.........................................................................

Step 28 - Filament sensor installation (optional)

....................................................

Step 29 - Connecting the filament sensor (optional)

............................................

Step 30 - Covering the electronics

...........................................................................

Step 31 - Haribo time!

..................................................................................................

Step 32 - Spool holder parts preparation

.................................................................

Step 33 - Spool holder parts preparation

................................................................

Step 34 - Assembling the spool holder base(s)

......................................................

Step 35 - Adding the spool holder rails

....................................................................

Step 36 - Adjusting the spool holder width

............................................................

Step 37 - Attaching anti-slip pads

............................................................................

Step 38 - Haribo time!

.................................................................................................

Step 39 - Finalising the assembly

.............................................................................

Step 40 - Connecting the PSU

..................................................................................

Step 41 - What is next?

...............................................................................................

Summary of Contents for MINI+

































Search results

Summary of Contents for MINI+

Reviews:

Related manuals for MINI+

Brands by name

Popular brands

Prusa Research MINI+, Manual

Search results

Summary of Contents for MINI+

Reviews:

Related manuals for MINI+

Brands by name

Popular brands