background image

 

Dual-band V solid dipole 30-40m (6m)   – V1.0E

PST-34TV 

Assemblyng instructions:

The antenna can be assembled in different ways:
Assemble it on two sawhorses and then carry it on the mast or pre-assemble the elements and then complete 
the assembly on the mast.
In both cases it is preferable to prepare before the elements and then the main plate assembly. 
Extracting elements from the carton box, you will find the element tubes as pre-assembled elements, in a 
telescopic set. Tilt the tube set, make sure that all heads of each diameter escape from the main pipe. 

Do not forget to lubricate the thread of steel bolts, if  dry may stiff them.

Place the element on a plan, and begin to assembly the smaller diameter,
Align the hole of the inner tube with hole of the outer tube. The fastening of the elements takes place by 
inserting the bolt from the larger  hole so that the cylindrical bolt head pass thoroughly and rests on the inner 
tube fig.2. 
Some sections are multi-perforated to facilitate the adjustment, always start from the center hole, and then 
shorten or lengthen it if antenna is too long or too short.
Using the same technique, extract and splicing all sections and traps.
Tighten the nut. Make sure that all bolts heads are on the same side. 

Insert the set of coils (30m on the inner side,  20m  trap with the tip of 40m end on the outer side). 

Some inner ends have more holes, they will help you in tuning antenna on your preferite band section, use 
the one in the middle for now.

 

Start the eventual calibration  from the highest frequency (30m) and after the 40m tip end. 
Longer antenna arm lower the resonance, shorter antenna arm increase the resonance. 

Any drainage holes present on the traps, at the end of assembly should be down side. 

Do not seal traps or tube joints. Antenna must breath to prevent damages due condensation.

Half dipole tapering (

net of overlaps)

d

45 75cm - 

d

40 105cm - 

d

35 104cm (with coil) - 

d

30 125cm - 

d

25 140cm – 

d

20 //T30// - 

d

16 20cm - 

d

12 90cm

On 

d

25 there are 5 holes for 30m tune, step 5cm, on 

d

12 there are  4 holes for 40m tune.

--------------------()()()()()-----------------| T30 |--------------

Summary of Contents for PST-34TV

Page 1: ...the inner tube fig 2 Some sections are multi perforated to facilitate the adjustment always start from the center hole and then shorten or lengthen it if antenna is too long or too short Using the same technique extract and splicing all sections and traps Tighten the nut Make sure that all bolts heads are on the same side Insert the set of coils 30m on the inner side 20m trap with the tip of 40m e...

Page 2: ...m If too long the antenna will resonate slightly lower Seal the coax with good quality sealing glues The balun improves antenna operation prevent there being return RF currents on the shield of the coaxial cable that could cause TVI phenomena or other RF interference When assembled the antenna must have a look like the one pictured After completing the tune up check the tightness of all nuts If th...

Page 3: ...ius about 5 3m Wind area about 0 3m2 Mast diameter 40 50mm Weight about 10kg Max wind 130Km Material Alluminum 6060 T6 SS hardware Performance The antenna has sufficient bandwidth to cover the whole assigned segment on both bands maximum SWR of 2 1 to extremes or better if SWR in band center is less than 1 5 1 Performance may vary depending on the environmental conditions in which the antenna is i...

Page 4: ... worked and finished with the best care possible allowed by the state of art Use it within the rating for which it was built and will serve you faithfully for many years In case of doubts or concerns our technical department is always ready to provide all the necessary help If you are satisfied tell the others otherwise tell to us Your opinion and your suggestions will help us to improve even more...

Reviews: