VIZZ
®
LED HEADLAMP
ENGLISH
Battery Installation - See Figure 1
3 AAA
• Alkaline (LR03)
• Lithium (L92)
• Rechargeable NiCad or NiMH
Princeton Tec cares about the environment
and recommends recycling batteries. For
more information about battery recycling,
please go
to www.batteryrecycling.com.
Observe proper battery polarity. Improper
installation of the batteries will damage the
light and void the warranty.
WARNING
!
• Never mix fresh and used batteries.
• Never mix different battery brands or
chemistry types.
• Always remove drained batteries immediately.
• Remove batteries during long periods of
storage.
NOTE: Lithium batteries offer extended
constant brightness time, extreme cold weather
performance, and lighter weight. Rechargeable
NiCad or NiMH batteries may result in reduced
brightness due to lower nominal voltage.
The Vizz battery compartment has a waterproof
seal. It is important to keep this seal free from
dirt and away from harsh chemicals in order
to preserve waterproof integrity. Inspect the
seal every time batteries are changed. If dirt is
present, wipe gently with a damp cotton swab
and mild soap until dirt is removed.
Switch Operation -
See Figure 2
From off:
One press - Red Ultrabright LEDs
Two presses - Maxbright LED
Three Presses - White Ultrabright LEDs
Five second hold - Lockout
On in any mode:
Hold - Dimming
Press after more than two seconds - Off
A single press more than two seconds after
the previous button press will turn light off.
From off state, 5 second hold will lock light to
prevent accidental turn on and resulting battery
drain. The Indicator LED (located inside the
power button) will blink three times to confirm
lock. 5 Second hold from the locked state will
unlock the light and the indicator LED will flash
to confirm unlock. Removal and replacement of
batteries will also reset Vizz to unlocked state.
Troubleshooting
If the Vizz fails to light:
• Check the batteries for proper installation.
• Replace batteries if proper installation is
confirmed.
Princeton Tec reserves the right to change
product specifications without notice.
FOR CALIFORNIA RESIDENTS:
WARNING: This product contains Bisphenol A
(BpA) a chemical known to the State of California
to cause birth defects or other reproductive
harm.
Return Policy
If your light fails to operate, follow these
simple steps:
Check batteries. Replace if necessary.
1. To send your light in for repair or replacement,
first contact Princeton Tec customer service on
1-800-257-9080 to request an RMA number.
Please have your light model, date of purchase
and a brief description of the fault you are
experiencing. No warranty repairs will be
accepted without an RMA number.
2. Return the light without batteries to: Princeton
Tec, PO Box 8057 Trenton NJ 08650. Postage
due and freight collect items will not be
accepted.
3. Upon receipt your light will be processed in
about two weeks. Please allow additional time
for return transportation from NJ.
Princeton Tec
PO Box 8057,
Trenton, NJ 08650
Phone: 609-298-9331
Fax: 609-298-9601
princetontec.com
© 2018 Princeton Tec
Figure 2 – Switch Operation
Modes de fonctionnement
Schalterbetätigung
24
78
S P O T
WHITE
R E D
16
0
DISTANCE
(METERS)
Total
110 H
Regulated
1H
Total
104 H
Regulated
6 H
Total
150 H
Regulated
16 H
BEAM DISTANCE
3 MODES / DIMMABLE
T
= Time/ Zeit/ Temps
Time/
Temps
78 m
24 m
16 m
78 m 17 m
22 m
14 m
10 m
8 m
0 H
0.5 H 10 H
Time/
Temps
•
Princeton Tec calculates total burn time as the time it takes for the light source to produce a minimum of
0.25 lux at 2 meters. 0.25 lux is about the equivalent of a full moon on a clear night.
•
Princeton Tec berechnet die Gesamtbrenndauer bezogen auf eine von der Stirnlampe erzeugte minimale
Beleuchtungsstärke von 0,25 Lux in 2 Meter Abstand. 0,25 Lux entsprechen in etwa der Beleuch-
tungsstärke des Vollmonds in einer klaren Nacht.
•
Princeton Tec définit la durée totale d’éclairage comme le temps nécessaire à la source
lumineuse pour produire un minimum de 0,25 lux à 2 mètres. 0,25 lux équivaut à peu près à la
luminosité d’une pleine lune dans un ciel nocturne dégagé.
Figure 1 – Battery Replacement
Remplacement des piles
Batteriewechsel
1
2
3
4
031
8
SINGLE PRESS
RED ULTRABRIGHT LEDs
HOLD FROM ON
DIMMABLE ALL MODES
DOUBLE PRESS
MAXBRIGHT LED
HOLD FROM OFF
(
5 SECONDS)
LOCK OR UNLOCK
TRIPLE PRESS
WHITE ULTRABRIGHT LEDs
SINGLE PRESS
TURNS LIGHT OFF
R
R
• Check circuit board for water (the seal may
have been compromised by improper rear
cover installation or dirty seal). The light will
resume normal operation once the water
is shaken or blown out and the light is left
open until completely dry. If the light has
been contaminated with salt water, flush
the unit with fresh water and dry as
described above.
USA Lifetime Warranty - International
10-YearWarranty
Due to International regulations, Princeton
Tec’s lifetime warranty can only be offered to
customers in the USA. Princeton Tec offers a
10-year warranty to our customers outside
the USA. FULL WARRANTY - Princeton Tec
warrants this product to be free from defects
in workmanship and materials under normal
use for as long as you own this product. This
warranty covers all of the component parts of
the product except batteries. This warranty does
not cover deterioration due to normal wear or
damage due to misuse, alteration, negligence,
accidents, or unauthorized repair. Princeton Tec
will repair or replace parts which are defective
in workmanship or materials. Your authorized
Princeton Tec Dealer and Princeton Tec are the
only facilities authorized to repair the product.
After (3) unsuccessful attempts to repair the
product, you have the right to elect replacement
of the product or a refund of the purchase
price less allowance for use of the product. NO
INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARE INCLUDED IN THIS WARRANTY. (Some
states do not allow the exclusion or limitation
of incidental or consequential damages, so the
above limitations or exclusions may not apply
to you.) This warranty gives you specific legal
rights, and you may also have other rights which
vary from state to state.
