1. Set a period of time for the timer
to be “ON”
Locate the gray pins and push them
DOWN at the marked times when the
attached device is to be “ON”. Each pin
represents a 30 minute time interval.
2. Set the “CURRENT TIME”
Rotate the entire gray push-pin dial
clockwise until the arrow marked
“CURRENT TIME” aligns with the
current time of day on the dial. “AM”
hours are highlighted in WHITE. “PM”
hours are highlighted in BLACK.
3. Set “BYPASS SWITCH”
When the switch is in the “TIMER ON”
position, timer will automatically turn the
attached device on and off. When the
switch is in the “OUTLET ON” position,
timer will bypass the programming and
the attached device will remain on.
4. Plug timer into an
ELECTRICAL OUTLET
5. Attach ONE DEVICE to the timer
Plug the device into the outlet on the
front of the timer.
LIMITED 1 YEAR WARRANTY
Prime warrants to the original consumer purchaser, and solely for the
benefit of such original consumer purchaser (the "Consumer"), that
the Power Zone timer product to be free from manufacturing defects
for a period of one year from the original date of purchase (“warranty
period”). This warranty is limited to the repair or replacement of this
product only and Prime is not liable for any consequential or
incidental damage to other products that may be used with this unit.
This warranty is effective only if such unit is returned to Prime not
later than thirty (30) days after the expiration of the warranty period.
Warranty is void if damage is due to neglect, misuse, alteration,
modification, improper installation, or repair by other than Prime. This
warranty is in lieu of all other warranties express or implied. Some
states do not allow limitations on how long an implied warranty lasts
or permit the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you.
It is our experience that a product that fails prematurely due to a
manufacturing defect in materials or workmanship, will generally do
so very early in the product’s life cycle, often the first or second time
the product is used. Products that are returned for warranty
inspection after months or years of continuous reliable service are
usually the result of normal wear and tear, which is not considered a
defect in materials or workmanship and therefore is not covered by
the warranty.
This warranty gives you specific rights, and you may also have other
rights which vary from state to state. If unit should prove defective
within the warranty period, return within the time period set forth
above prepaid with the original purchase receipt to:
Prime Wire & Cable, Inc.
Attention: Quality Assurance Manager
Power Zone products
280 Machlin Court
City of Industry, CA 91789
www.powerzone.primewirecable.com
24-Hour
Mechanical Timer
Model: 900-1165
WARNING
Risk of Electric Shock
Keep children away. Unplug timer before cleaning. Fully insert plug. Do not use
in wet locations.
Risk of Fire
Do not use to control appliances that contain heating elements (cooking
appliances, heaters, irons, etc.). Do not exceed electrical ratings. For Indoor
Use Only.
STEP-BY-STEP INSTRUCTIONS
HELPFUL TIPS
• This timer repeats the same settings daily.
• To push down or pull up the gray pins, use your finger or the
tip of a small non-metalic insulated tool, such as a pencil or
toothpick.
• Set up to 48 different “ON” and “OFF” times in a 24 hour period
by the positioning of the gray pins. Pins pressed down represent
the ‘ON’ time. Pins in the up position represent ‘OFF’ time.
• Switching the timer to “OUTLET ON” will bypass programming,
however, the timer dial will continue to rotate and maintain
the current time.
IN CASE OF POWER FAILURE
Timer will stop operating if the power goes out. Once power is
restored, reset the time of day as explained in Step 2 of the
instructions.
SAFETY INFORMATION
& SPECIFICATIONS
THIS TIMER IS A “POLARIZED” DEVICE
One blade on the male plug is wider than the other and
is only intended for use with a polarized outlet. Use with
a three-pronged grounded outlet is also acceptable.
THIS TIMER IS FOR USE WITH A 125VAC POWER SOURCE.
125VAC / 60Hz
DO NOT ATTACH A DEVICE THAT EXCEEDS THE UNIT RATINGS:
15A / 1875W Resistive
(General Purpose)
10A / 1250W Tungsten
(Incandescent)
1/2 HP
(Horsepower Motor)
ENGLISH FRONT ONLY
