Remote Control Transmitter Fob-CM1
Programming Instructions
Pairing Key-Fob Remote Control:
1. Press and hold the PROGRAM button on the top of the
unit for 3 seconds until the LED turns green (HPU will also
beep). The unit is now ready to be paired with the key-fob
remote control.
NOTE
: If dual units are installed, repeat Steps 1–3 to pair
multiple units to a single remote control. Up to (10)
wireless controllers can be programmed to each unit.
2. Press the UP button on the key-fob remote control for one
second and release. The green LED on the unit(s) will
initially turn off, then flash green steadily (HPU will also
beep) indicating that the pairing is complete.
3. Test the paired remote control by pressing the UP
and the DOWN button to ensure that the anchor
is responding.
PROGRAM
LED
Hydraulic Pump Unit (HPU)
MICRO Driver Unit
LED
PROGRAM
2
9010 Palm River Road, Tampa, FL 33619
phone 813.689.9932 • fax 813. 689.8883
www.power-pole.com
Need help? Contact our Technical Support Team at
1 + 813.689.9932 Option 2
©2018 all rights reserved. Power-Pole Shallow Water Anchor
U.S. Patent No. 6,041,730
To raise or lower the spike, press and hold either the
UP
or
DOWN
button on the remote control. The anchor will only
continue to move so long as you keep the button depressed.
Auto Mode
: Double tapping (pressing and releasing 2 times
within 1 second) either the
UP
or the
DOWN
buttonon the
remote control will cause the anchor to retract or deploy au-
tomatically. The anchor will continue to move in said direction
until it either retracts completely (up) or senses a solid bottom
surface (down).
Battery Replacement:
1.
Ensure the surrounding area is as dry as possible to avoid
any moisture intrusion.
2.
Use a small screwdriver to remove the Key-Fob cover. (
FIG. 1
)
3.
Remove the rubber membrane and the circuit board from
the Key-Fob.
4.
Remove the battery from the holder on the front of circuit
board and replace with any CR2032 3V Lithium Coin
Battery. (
FIG. 2
)
5.
Place the circuit board and rubber membrane back into
the Key-Fob base and ensure that the rubber membrane
is seated properly prior to installing the cover. (
FIG. 3
)
Operating Instructions
For Technical Support Call 813.689.9932 option 2
Programming Instructions
Key Fob Remote Control
Featuring Technology
Pairing Key-Fob Remote Control:
1.
Press and hold the PROGRAM button on the top of the
unit for 3 seconds until the LED turns green (HPU will
also beep). The unit is now ready to be paired with the
key-fob remote control.
NOTE: If dual units are installed, repeat Steps 1–3 to pair
multiple units to a single remote control. Up to (10)
wireless controllers can be programmed to each unit.
2.
Press the UP button on the key-fob remote control for
one second and release. The green LED on the unit(s)
will initially turn off, then flash green steadily (HPU will
also beep) indicating that the pairing is complete.
3.
Test the paired remote control by pressing the UP
and the DOWN button to ensure that the anchor
is responding.
PROGRAM
LED
Hydraulic Pump Unit (HPU)
MICRO Driver Unit
LED
PROGRAM
To activate your warranty or find a Power-Pole Certified
Warranty Center, go to
www.power-pole.com
2
For Technical Support Call 813.689.9932 option 2
9010 Palm River Road, Tampa, FL 33619 • phone 813.689.9932
fax 813. 689.8883 •
www.power-pole.com
To raise or lower the spike, press and hold either the
UP
or
DOWN
button on the remote control. The anchor will only
continue to move so long as you keep the button depressed.
Auto Mode:
Double tapping (pressing and releasing 2 times
within 1 second) either the
UP
or the
DOWN
button
on the remote control will cause the anchor to retract or
deploy automatically. The anchor will continue to move
in said direction until it either retracts completely (up) or
senses a solid bottom surface (down).
Battery Replacement:
1.
Ensure the surrounding area is as dry as possible to avoid
any moisture intrusion.
2.
Use a small screwdriver to remove the Key-Fob cover.
(Figure 1)
3.
Remove the rubber membrane and the circuit board from
the Key-Fob.
4.
Remove the battery from the holder on the front of circuit
board and replace with any
CR2032 3V
Lithium Coin
Battery.
(Figure 2)
5.
Place the circuit board and rubber membrane back into
the Key-Fob base and ensure that the rubber membrane
is seated properly prior to installing the cover.
(Figure 3)
Operating Instructions
Figure 1
Figure 2
Figure 3
For Technical Support Call 813.689.9932 option 2
Programming Instructions
Key Fob Remote Control
Featuring Technology
Pairing Key-Fob Remote Control:
1.
Press and hold the PROGRAM button on the top of the
unit for 3 seconds until the LED turns green (HPU will
also beep). The unit is now ready to be paired with the
key-fob remote control.
NOTE: If dual units are installed, repeat Steps 1–3 to pair
multiple units to a single remote control. Up to (10)
wireless controllers can be programmed to each unit.
2.
Press the UP button on the key-fob remote control for
one second and release. The green LED on the unit(s)
will initially turn off, then flash green steadily (HPU will
also beep) indicating that the pairing is complete.
3.
Test the paired remote control by pressing the UP
and the DOWN button to ensure that the anchor
is responding.
PROGRAM
LED
Hydraulic Pump Unit (HPU)
MICRO Driver Unit
LED
PROGRAM
To activate your warranty or find a Power-Pole Certified
Warranty Center, go to
www.power-pole.com
2
For Technical Support Call 813.689.9932 option 2
9010 Palm River Road, Tampa, FL 33619 • phone 813.689.9932
fax 813. 689.8883 •
www.power-pole.com
To raise or lower the spike, press and hold either the
UP
or
DOWN
button on the remote control. The anchor will only
continue to move so long as you keep the button depressed.
Auto Mode:
Double tapping (pressing and releasing 2 times
within 1 second) either the
UP
or the
DOWN
button
on the remote control will cause the anchor to retract or
deploy automatically. The anchor will continue to move
in said direction until it either retracts completely (up) or
senses a solid bottom surface (down).
Battery Replacement:
1.
Ensure the surrounding area is as dry as possible to avoid
any moisture intrusion.
2.
Use a small screwdriver to remove the Key-Fob cover.
(Figure 1)
3.
Remove the rubber membrane and the circuit board from
the Key-Fob.
4.
Remove the battery from the holder on the front of circuit
board and replace with any
CR2032 3V
Lithium Coin
Battery.
(Figure 2)
5.
Place the circuit board and rubber membrane back into
the Key-Fob base and ensure that the rubber membrane
is seated properly prior to installing the cover.
(Figure 3)
Operating Instructions
Figure 1
Figure 2
Figure 3
For Technical Support Call 813.689.9932 option 2
Programming Instructions
Key Fob Remote Control
Featuring Technology
Pairing Key-Fob Remote Control:
1.
Press and hold the PROGRAM button on the top of the
unit for 3 seconds until the LED turns green (HPU will
also beep). The unit is now ready to be paired with the
key-fob remote control.
NOTE: If dual units are installed, repeat Steps 1–3 to pair
multiple units to a single remote control. Up to (10)
wireless controllers can be programmed to each unit.
2.
Press the UP button on the key-fob remote control for
one second and release. The green LED on the unit(s)
will initially turn off, then flash green steadily (HPU will
also beep) indicating that the pairing is complete.
3.
Test the paired remote control by pressing the UP
and the DOWN button to ensure that the anchor
is responding.
PROGRAM
LED
Hydraulic Pump Unit (HPU)
MICRO Driver Unit
LED
PROGRAM
To activate your warranty or find a Power-Pole Certified
Warranty Center, go to
www.power-pole.com
2
For Technical Support Call 813.689.9932 option 2
9010 Palm River Road, Tampa, FL 33619 • phone 813.689.9932
fax 813. 689.8883 •
www.power-pole.com
To raise or lower the spike, press and hold either the
UP
or
DOWN
button on the remote control. The anchor will only
continue to move so long as you keep the button depressed.
Auto Mode:
Double tapping (pressing and releasing 2 times
within 1 second) either the
UP
or the
DOWN
button
on the remote control will cause the anchor to retract or
deploy automatically. The anchor will continue to move
in said direction until it either retracts completely (up) or
senses a solid bottom surface (down).
Battery Replacement:
1.
Ensure the surrounding area is as dry as possible to avoid
any moisture intrusion.
2.
Use a small screwdriver to remove the Key-Fob cover.
(Figure 1)
3.
Remove the rubber membrane and the circuit board from
the Key-Fob.
4.
Remove the battery from the holder on the front of circuit
board and replace with any
CR2032 3V
Lithium Coin
Battery.
(Figure 2)
5.
Place the circuit board and rubber membrane back into
the Key-Fob base and ensure that the rubber membrane
is seated properly prior to installing the cover.
(Figure 3)
Operating Instructions
Figure 1
Figure 2
Figure 3
To activate your warranty or find a Power-Pole Certified Warranty Center,
go to
www.power-pole.com
