Power Climber Wind BAP 360 Operation And Installation Instructions Manual Download

Page: 1 / 37

Reference: 38741

Issue date: 2018-JUL-24

Revision: L

Page 1 of 37

BLADE ACCESS PLATFORM

TYPE: BAP 360°

OPERATION AND INSTALLATION INSTRUCTIONS

CONFORM TO THE

MACHINE DIRECTIVE 2006/42/EC

EN 1808 was used as guiding base for the design

WARNING:



All persons operating this equipment must read and completely understand this manual.



All persons must be thoroughly trained in the use of the equipment, it’s operational and
safety features, and they must also be capable of carrying out the daily checklist.



Only authorized and physically fit persons shall operate the equipment.



Any operation in violation of these instructions is at the operator’s own risk and may result
in serious injuries.



Keep this manual with the platform at all times.



Only use spare parts and steel wire rope from POWER CLIMBE

R WIND

Summary of Contents for BAP 360






































Search results

Summary of Contents for BAP 360

Reviews:

Related manuals for BAP 360

Brands by name

Popular brands

Power Climber Wind BAP 360, Operation And Installation Instructions Manual

Search results

Summary of Contents for BAP 360

Reviews:

Related manuals for BAP 360

Brands by name

Popular brands