![background image](http://html1.mh-extra.com/html/polar-electro/equine-rs300x-g31/equine-rs300x-g31_getting-started-manual_1571579001.webp)
Polar Equine
RS300X G31
- Getting started guide -
1. Contents of the set
A. A RS300X receiver:
receives and dis-
plays all the data measured by the T54H
transmitter and the G1 sensor.
B. A G1 GPS sensor with its battery:
measures speed and distance in real time.
C. A T54H transmitter:
measures the
horse’s heart rate in real time.
2. How to use the RS300X receiver
The RS300X receiver has 5 navigation buttons.
•
Use
UP
and
DOWN
to scroll through
the different menus and adjust values (a
bit like + and - buttons).
•
Use
OK
to enter a menu, to validate a
value and to start the stopwatch.
•
Use
STOP
to exit a menu, to return to
the previous display (when you made a
mistake while adjusting a value) and to
stop the stopwatch.
•
Press
LIGHT
once and the backlight is
activated for 5 seconds when you press
any other button. You can also lock the
buttons by pressing and holding the
LIGHT
button for 2 seconds.
3. Starting the RS300CX
By default, the RS300X receiver is
switched off to save the battery.
Press
OK
twice to activate it.
Press
UP
or
DOWN
to select english
as the language to be used.
Press
OK
to validate.
The following settings must be done,
even though they don’t concern the
horse.
If you don’t do these basic settings,
the RS300X will remind you again be-
fore every exercise.
Use the
UP
and
DOWN
buttons to cus-
tomize the following basic settings.
Press
OK
to validate your settings.
•
Time display (24h/12h)
•
Time
•
Date (day/month/year or
month/day/year)
•
Units (kg/cm/km or lb/ft/mi)
•
Weight (of the rider)
•
Height (of the rider)
•
Birthday (day/month/year or
month/day/year) of the rider
•
Sex (of the rider)
If you made a mistake somewhere,
press
STOP
to return to the previous
setting.
If your settings are good, select Yes.
Press
OK
to validate.
Once the settings are done, the RS300X
returns automatically to the time display.
It is now ready for use!
4. Starting the G1 GPS Sensor
The G1 sensor uses GPS (Global Positioning System) technology to measure speed
and distance in real time. In ideal conditions of use, its precision can reach one meter.
The battery of the G1 has an average of 10h of use. The G1 is waterproof and its solid
design makes it resistant to most shocks and scratches.
Use a coin to unscrew and open the metal battery cover. Place the LR6 battery as indi-
cated and screw the metal cover back into place.
The buckle located in the back of the G1
allows you either to wear the G1 on your
arm using the strap provided or to fix it
on a belt or loop.
To ensure a good detection of the GPS
signals, the G1 should not be covered or
worn under clothes.
Open the G1 buckle and pass the strap
through the loop (Velcro on the inside).
Pull in enough strap so your arm can fit
through it.
Then adjust the size of the strap so the G1
can’t move once placed on your arm.
To ensure good detection of the GPS sig-
nals, the G1 shouldn’t be covered and
should be placed with the Polar logo in an
upright position. We also recommend wear-
ing it on the same arm as the RS300X re-
ceiver.
Your G1 is now ready for use!
Press the button 2 seconds to start (or stop)
the G1. A green light indicating battery status
(
B
) flashes for a few seconds. Following this,
a red light indicating detection status (
A
) ap-
pears and shows that the G1 is searching for
GPS signals.
Don’t move. Once the GPS signals have
been found (after 1 minute in average), this
light (
A
) turns green.
Note:
The light indicating battery status (B)
turns red when the battery is flat .
B.
A.
C.