background image

1

VENT-FREE

GAS LOG SET

 MODEL # VFL2-VO24DR

VFL2-RO24DR

VFL2-VO30DR

VFL2-RO30DR

VFL2-MO24DR

VFL2-MO30DR

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

WARNING: IF THE INFORMATION IN THIS MANUAL IS NOT FOLLOWED 

EXACTLY, A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY 

DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

The Installation instructions for an appliance for installation on combustible flooring 

shall specify that when the appliance is installed directly on carpeting, tile or other 

combustible material, other than wood flooring, the appliance shall be installed on a 

metal or wood panel extending the full width and depth of the appliance.

       WARNING:

 

This appliance 

is equipped for (Natural and 

Propane) gas. Field conversion 

is not permitted other than 

between natural or propane 

gases.

- Do not store or use gasoline or other flammable vapors and Iiquids in vicinity of

this or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas

supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency

or the gas supplier.

This is an unvented gas-fired heater. It uses air (oxygen) from the room in which it is 

installed. Provisions for adequate combustion and ventilation air must be provided.

Refer to Air For Combustion and Ventilation section on page 8 of this manual.

This appliance may be installed in an aftermarket, permanently located manufactured (mobile) 

home, where not prohibited by local codes. This appliance is only for use with propane or 

natural gas. This appliance is equipped with a simple means to switch between propane and 

natural gas. Field conversion by any other means including the use of a kit is not permitted.

Dual Fuel

80-10-443 - 2018-06-01

CAUTION - FOR YOUR SAFETY

ANS Z21.11.2 2013

Questions, problems, missing parts?

 Before returning to your retailer, call our customer 

service department at 1-877-447-4768,

 

8:30 a.m. –  4:30

 

p.m., CST, Monday – Friday or 

email us at [email protected].

NG

LP

C           US

C           US

Patent Pending Dual 

Fuel System

Summary of Contents for VFL2-MO24DR











Reviews: