background image

Copyright

Copyright © 2003 by PLANET Technology Corp. All rights reserved. No part 

of this publication may be reproduced, transmitted, transcribed, stored in a 

retrieval system, or translated into any language or computer language, in any 

form  or  by  any  means,  electronic,  mechanical,  magnetic,  optical,  chemical, 

manual or otherwise, without the prior written permission of PLANET.

PLANET makes no representations or warranties, either expressed or implied, 

with respect to the contents hereof and specifically disclaims any warranties, 

merchantability or fitness for any particular purpose. Any software described 

in this manual is sold or licensed “as is”. Should the programs prove defec-

tive  following  their  purchase,  the  buyer  (and  not  PLANET,  its  distributor,  or 

its dealer) assumes the entire cost of all necessary servicing, repair, and any 

incidental or consequential damages resulting from any defect in the software. 

Further,  PLANET  reserves  the  right  to  revise  this  publication  and  to  make 

changes from time to time in the contents hereof without obligation to notify 

any person of such revision or changes.

All brand and product names mentioned in this manual are trademarks and/or 

registered trademarks of their respective holders.

FCC Regulation

This device complies with part 15 of the FCC rules. Operation is subject to the 

following two conditions: (1) This device may not cause harmful interference 

and (2) this device must accept any interference received, including interfer-

ence that may cause undesired operation.

Revision

Quick Installation Guide for PLANET 2.4GHz WLAN Booster

Model: WBT-500/1000

Rev: 1.0 (December, 2003)

Part No. EMQ-WBT

Summary of Contents for WBT-1000











Reviews: