![background image](http://html.mh-extra.com/html/pioneer/cd-r55/cd-r55_owners-manual_330982001.webp)
Owner
’
s
Manual
Remote
control
CD-R55
Published by Pioneer Corporation.
Copyright © 2006 by Pioneer Corporation.
All rights reserved.
Printed in China
<CZR5072-A> E
<KMMZX> <06K00000>
a
2 3
k
l
j
f
g
h
4
d
e
c
b
8
6
5
7
i
1
9
!
When using for the first time, pull out the
film protruding from the tray.
WARNING
!
Handling the cord on this product or cords as-
sociated with accessories sold with the pro-
duct may expose you to chemicals listed on
proposition 65 known to the State of California
and other governmental entities to cause can-
cer and birth defects or other reproductive
harm.
Wash hands after handling
.
!
Keep the battery out of the reach of children.
Should the battery be swallowed, immediately
consult a doctor.
CAUTION
!
Do not allow this unit to come into contact
with liquids. Electrical shock could result.
Also, this unit damage, smoke, and overheat
could result from contact with liquids.
!
Do not disassemble or modify this unit. To do
so may cause a malfunction.
!
Always keep the volume low enough so that
you can hear sounds from outside the vehicle.
!
Use only one
CR2025 (3 V)
lithium battery.
!
Always check carefully that you are loading
the battery with its plus (+) and minus (
–
)
poles facing in the proper directions.
!
Remove the battery if the remote control is not
used for a month or longer.
!
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
!
Do not handle the battery with metallic tools.
!
Do not store the battery with metallic materials.
!
In the event of battery leakage, wipe the re-
mote control completely clean and install a
new battery.
!
When disposing of used batteries, please
comply with governmental regulations or en-
vironmental public institutions
’
rules that
apply in your country/area.
!
“
Perchlorate Material
–
special handling may apply.
See www.dtsc.ca.gov/hazardouswaste/perchlorate.
(Applicable to California, U.S.A.)
”
Using the remote control
Point the remote control in the direction of the
front panel to operate.
!
The remote control may not function prop-
erly in direct sunlight.
Important
!
Do not store the remote control in high tem-
peratures or direct sunlight.
!
Do not let the remote control fall onto the
floor, where it may become jammed under the
brake or accelerator pedal.
Using the remote control
operation mode switch
There are three remote control operation
modes on the remote control.
AVH
mode operation
When operating an AV Receiver (e.g., AVH-
P5900DVD) with this remote control, the mode
is normally switched to
AVH
.
DVD
mode operation
When operating a Pioneer DVD player (e.g.,
XDV-P6) with this remote control, the mode is
switched to
DVD
. If you switch the mode to
DVD
, the joystick and
0
to
10
operations are
changed for DVD player.
TV
mode operation
When operating a Pioneer TV tuner (e.g., GEX-
P5700TV (P)) with this remote control, the
mode is switched to
TV
. If you switch the
mode to
TV
, the joystick operation is changed
for TV tuner.
In
TV
mode, only buttons shown below can be used.
!
SOURCE
button
!
ATT
button
!
VOLUME
buttons
!
Joystick
!
DIRECT
button
!
REAR SOURCE
button
Setting remote control
code type
When the remote control operation mode switch is
set to
DVD
, changing the remote control code type
enables you to operate the Pioneer DVD player with
this remote control. There are three remote codes,
code type
A
, code type
B
and code type
AVH
.
!
When operating an AV Receiver (e.g., AVH-
P5900DVD), select code
AVH
.
!
When operating a multi-DVD player (e.g.,
XDV-P6), select code
A
.
!
When operating a DVD navigation unit, se-
lect code
B
.
1
Set the remote control selection switch
on the left side of the remote control to
the appropriate position with a pen tip or
other pointed instrument .
!
If you select
AVH
mode, there is no need to
take the following procedure.
!
If you select
A
/
B
mode, take the following
procedure and change the code type to the
appropriate type.
2
Press 0 and CLEAR on the remote con-
trol simultaneously to change the code
type.
Initially, the code type is set to
A
. Each time
you press
0
and
CLEAR
simultaneously on the
remote control the code type switches be-
tween
A
and
B
.
Specifications
Power source ............................. 3 V DC (Lithium battery;
CR2025)
Dimensions (W × H × D) ... 54 × 149 × 13 mm
(2-1/8 × 5-7/8 × 1/2 in.)
Weight .......................................... 59 g (2 oz) (including bat-
tery)
Infrared remote control
Wavelength ................................. 945 nm
Output ........................................... typ; 10 mw/sr per Infrared
LED
Note
Specifications and the design are subject to pos-
sible modifications without notice due to im-
provements.
Before You Start
En