background image

Published by LX-KM 1208 AVM

Printed in the Netherlands

MCM1055/51/98

Subject to modi cation

EN

Micro Audio System

Contents

Page

Contents

Page

©Copyright 2012 Philips Consumer Electronics B.V. Eindhoven, The Netherlands.
All rights reserved.  No part of this publication may be reproduced, stored in a 
retrieval system or transmitted, in any form or by any means, electronic, 
mechanical, photocopying, or otherwise without the prior permission of Philips.

Version 1.0

1 Technical Specification and Connection Facilities

2  Laser Beam Safety Precautions......................................... 2-1

3  Important Safety Precautions .................................. 3-1 to 3-2

4  Safety Check After Servicing ............................................. 4-1

6  Standard Notes For Servicing,Lead Free Requirements
    & Handling Flat Pack IC .......................................... 6-1 to 6-4

5  Safety Information General Notes & Lead Free

7  Direction of Use ....................................................... 7-1 to 7-2

8  Cabinet Disassembly Instructions ........................... 8-1 to 8-2

12  Display Board

9 Troubleshooting ....................................................... 9-1 to 9-2

10  Block Diagram .................................................................10-1

11  Wiring Diagram ...............................................................11-1

13  Power Board

14  AMP Board

Layout Diagram.................................................12-7

15  Decoder Board 

16  Exploded View.....................................................................13-1

17  Revision List ........................................................................14-1

Circuit Diagram .................................................12-8

Layout Diagram ................................................12-9

.................................................1-1 to 1-8

Circuit Diagram ....................................................12-1

Layout Diagram ...................................................12-2

Circuit Diagram ................................................12-3

Circuit Diagram ............................................12-5 to 12-6

Layout Diagram ...............................................12-4

Requirements .................................................................... 5-1

Features

RDS

Voltage Selector
ECO Standby

DTS

Feature

Different

/98

/51

 

Summary of Contents for MCM1055/51/98






































Reviews: