Perun Airsoft V3 Optical Installation Manual Download | Manualshive

Page: 1 / 10

background image

1

V3

Optical

Installation manual

This is a manual for technicians, who will be installing Perun V3 Optical in the replica. Be sure
to also read the user manual, so that you can properly test the replica. Installation can only be
done by experienced airsoft technicians. The warranty does not cover damages resulting from
incompetent montage.

How does it work? ....................................................................................................................... 2

Compatibility ............................................................................................................................... 3

Compatible gearbox shells .......................................................................................................... 3

DSG .............................................................................................................................................. 3

Max Torque gears ........................................................................................................................ 3

Main spring rate and rate of fire ................................................................................................. 3

Batteries ...................................................................................................................................... 3

Perun V3 Optical installation ....................................................................................................... 4

First run ....................................................................................................................................... 7

Fuse ............................................................................................................................................. 7

Factory settings ........................................................................................................................... 7

Troubleshooting .......................................................................................................................... 8

1
2
3
...
»

Summary of Contents for V3 Optical











Reviews:

No comments

Related manuals for V3 Optical

Brand: ABB Pages: 11

Brand: Sagola Pages: 20

ECL Comfort 210

Brand: Danfoss Pages: 28

Brand: Carbatec Pages: 29

Brand: Moxa Technologies Pages: 2

Brand: YASKAWA Pages: 47

Phastite PH-8-HANDTOOL

Brand: Parker Pages: 10

TDI-Dynaload WCL488 Series

Brand: TDI Pages: 130

Brand: Mecc Alte spa Pages: 34

Brand: SilverBolt Pages: 9

AEROLYTE PRN 6060-A

Brand: Zero Pages: 33

Brand: HBM Pages: 96

Brand: IBASE Technology Pages: 81

Brand: James Walker Pages: 4

Brand: Kollmorgen Pages: 43

MELTEX PG Series

Brand: Nordson Pages: 16

Brand: SUHNER MACHINING Pages: 16

Brand: Quincy Pages: 78

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands