background image

System 2

TM

Modular Media Filters

O

W

N

E

R ’

S

M

A

N

U

A

L

INSTALLATION, OPERATION & PARTS

MODELS

PLM100

PLM125

PLM150

PLM175

PLM200

PLM300

OU

TLE

T

OU

TLE

T

REL

EAS

E

REL

EAS

E

OUT

LET

OU

TLE

T

REL

EAS

E

REL

EAS

E

This manual should be given to the
owner of this filter.

E

N

G

L

I

S

H

F

R

A

N
Ç

A

I

S

E
S
P
A

Ñ

O

L

Pentair Water Pool and Spa, Inc.

© 2012 Pentair Water Pool and Spa, Inc.

All rights reserved. This document is subject to change without notice.

1620 Hawkins Ave., Sanford, NC 27330 • (919) 566-8000
10951 West Los Angeles Ave., Moorpark, CA 93021 • (805) 553-5000

Trademarks and Disclaimers:

System 2™, Posi-Lok™,Sta-Rite

®

and Pentair Water Pool and Spa

®

are trademarks and/or registered trademarks of Pentair

Water Pool and Spa, Inc. and/or its affiliated companies in the United States and/or other counties. Unless noted, names
and brands of others that may be used in this document are not used to indicate an affiliation or endorsement between the
proprietors of these names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be the
trademarks or registered trademarks of those parties or others. Printed in U.S.A.

4-19-12

S338

(Rev. B)

Summary of Contents for STA-RITE PLM100













Reviews: