Pavilion GQ-C3260WX-FF PB US Installation Manual Download

Page: 1 / 68

FOR USE IN RESIDENTIAL OR MANUFACTURED HOME APPLICATIONS.

Installation must conform with local codes, or in the absence of local codes, the National Fuel Gas Code, ANSI Z223.1 / NFPA

54 - latest edition and/or the Natural Gas and Propane Installation Code CSA B149.1 - latest edition.

When applicable, installation must conform with the Manufactured Home Construction and Safety Standard, Title 24 CFR,

Part 3280 or the Canadian Standard CAN/CSA-Z240 MH Mobile Homes, Series M86.

PB Heat reserves the right to discontinue, or change at any time, the designs and/or specifications of its products without

notice.

Contact Pavilion Customer Center at 1-855-443-8468, if you have any questions or concerns.

CONDENSING TANKLESS GAS WATER HEATER

Installation Manual

Model : UT199DV (GQ-C3260WX-FF PB US)

Requests to Installers

• In order to use the Water Heater safely, read

this installation manual carefully, and follow the

installation instructions.

• Failures and damage caused by erroneous work

or work not as instructed in this manual are not

covered by the Pavilion Limited Warranty.

• Check that the installation was done properly in

accordance with this Installation Manual upon

completion.

• After completing installation, either place this

Installation Manual and Owner’s Guide (the

warranty registration information included) in

a plastic pouch and attach it to the side of the

Water Heater (or the inside of the pipe cover

or recess box if applicable), or hand it to the

customer to retain for future reference. For the

warranty conditions and limitations, see the

Owner’s Guide.

CAUTION

If the information in these instructions is not

followed exactly, a fire or explosion may result

causing property damage, personal injury or

death.
• Do not store or use gasoline or other

flammable vapors and liquids in the vicinity of

this or any other appliance.

• WHAT TO DO IF YOU SMELL GAS

- Do not try to light any appliance.

- Do not touch any electrical switch; do not use

any phone in your building.

- Immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier’s

instructions.

- If you cannot reach your gas supplier, call the

fire department.

• Installation and service must be performed by

a qualified installer, service agency or the gas

supplier.

WARNING

Low NOx Approved by SCAQMD

14 ng/J or 20 ppm

(Natural Gas Only)

SBB819E-1

Rev. 11/20

PB HEAT, LLC

Summary of Contents for GQ-C3260WX-FF PB US





































































Search results

Summary of Contents for GQ-C3260WX-FF PB US

Reviews:

Related manuals for GQ-C3260WX-FF PB US

Brands by name

Popular brands

Pavilion GQ-C3260WX-FF PB US, Installation Manual

Search results

Summary of Contents for GQ-C3260WX-FF PB US

Reviews:

Related manuals for GQ-C3260WX-FF PB US

Brands by name

Popular brands