background image

INSTRUCTIONS CM372

© Panduit Corp. 2008

FOR TECHNICAL SUPPORT www.panduit.com/resources/install_maintain.asp

(door removed from view for clarity)

(4) #10-32 Hex Nuts
(4) #10 Split Lock Washers
(4) #8-32 Hex Nuts
(4) #8 Split Lock Washers
(2) #6-32 Screws
(1) Grounding Cable
(4) Pieces of Fire Resistant Foam
(1) 26" length Grommet Edging
(1) 2 Position Surface Mount Box
     (

PANDUIT

 Part No. CBXJ2WH-A)

(1) 2' long Category TX6 Plus Patch Cord
     (

PANDUIT

 Part No. UTPSP2)

(1) Category TX6 Plus Jack Module
     (

PANDUIT

 Part No. CJ688TGWH)

#6-32 Screws

#8-32           #8

Hardware Guide

List of Common Components:

#10-32           #10

Hardware Guide

#10-32 Screws

PZWIFIENA

(2) 

P

AN

-T

Y

 mounts

     (

PANDUIT

 Part No. ABMM-A-C)

(4) 

P

AN

-T

Y

 Cable Ties

     (

PANDUIT

 Part No. PLT1.5I-C)

(1) Foam Retention Plate
(2) Keys
(2) Latching Wire Clips 
      (Panduit Part No. LWC50-A-L)
(4) #10-32 X 3/8” Thread Cutting 
Screws

(1) 1M STP TX6 Plus Patch Cord
      (

PANDUIT

 Part No. STP6X1MBU)

(1) Minicom TX6 Plus Shielded Jack
      (

PANDUIT

 Part No. CJS666TGY)

TABLE OF CONTENTS

 

Page (s)

Wall Mount Installation..................................................................................................................................................... 2
Ceiling Mount Installation..................................................................................................................................................2-4
Cisco Aironet 1250 Series Access Point Installation........................................................................................................ 5
Cable Routing....................................................................................................................................................................6
Antenna Installation...........................................................................................................................................................7
Fully Installed Application Photos......................................................................................................................................8

Keyed Knockout
Slots for Wall
Mount applications
(6 places)

Double Knockout 
for 1/2” or 3/4” Conduit
(3 places)

Brackets for 
Fire Resistant Foam (2 places) 

Knockout for
electrical 
junction box

#10-32 
Threaded
Grounding 
Studs

AIR-ANT514OV-R 
Knockouts for
Patch Antenna Mounting

AIR-ANT2430V-R Knockouts
for Patch Antenna Mounting

Knockouts for 
led lights 
on the wap 

Knockouts
for Surface
Raceway
(4 places)

RP-TNC 
Wall Mount 
bulkhead 
connector 
knockout
(6 places)

PZWIFIENA ONLY

PZWIFIENAS ONLY

Page 1 of 8

P

AN

Z

ONE

 

Wireless Access Point Enclosure

Part Numbers: PZWIFIENA, PZWIFIENAS

Summary of Contents for PANZONE PZWIFIENA









Reviews: