![background image](http://html.mh-extra.com/html/panasonic/wv-q160c/wv-q160c_operating-instructions_259831001.webp)
Preface
This ceiling mount bracket is exclusively designed to mount the network camera. Refer to the catalog or
the installation guide of the camera for supported cameras.
• WV-Q160C: Clear dome cover
• WV-Q160S: Smoked dome cover (approx. 50 % of transmittance)
Precautions
• Use only the specified camera.
Failure to observe this may cause a fall of an inappropriate camera resulting in injury or accidents.
Refer to the catalog or the installation guide of the camera for supported cameras
• Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is
produced.
Otherwise, the mounting portions will deteriorate and accidents such as a fall of the camera may
occur.
• Refer installation work to the dealer.
Installation work requires technique and experience. Failure to observe this may cause fire, electric
shock, injury, or damage to the product. Be sure to consult the dealer.
• Do not install this product in locations subject to vibration.
Loosening of mounting screws or bolts may cause'a fall of the product resulting in injury or acci-
dents.
• Install this product in a location high enough to avoid people and objects from bumping
the product.
Failure to observe this may cause injury.
• The measures of protection against a fall of the camera shall be taken.
Failure to observe this may cause a drop resulting in injury. Be sure to install this bracket-specific
safety wire.
• Periodic inspections shall be conducted.
Rust on the metal parts or screws may cause a fall of the product resulting in injury. Consult the
dealer for the inspections.
Parts and functions
Note:
• Remove the notch with a nipper.
• If a tiepin type microphone is used, mount the microphone on the rubber-made microphone stand.
Unless the microphone is used, cut the rubber with a nipper or conduct another treatment.
Important:
In order to avoid injury and to protect the cable, file the edge of the notch.
LOCK
OPEN
Notch for network cable,
monitor output cable, etc.
Dome cover
Ceiling mount bracket
Hole for microphone cable
Microphone stand*
Installations
Be sure to read "Precautions" before installation. The
Installation Guide of the network camera shall be read
as well.
1. Install the inner cover.
Slide the covers located on the both lateral sides
of the camera and put the inner cover on the
camera until the hooks inside the inner cover are
held in the holes of the camera (until a click is
heard).
Important:
Put the inner cover down on the cam-
era until the outside cover of the camera can-
not be seen from the opening (from which the
camera lens is visible) of the inner cover. If this
integration is not successfully performed, the
inner cover may be removed or the hidden part
at the top of the screen may become larger in
the WIDE mode.
Cover
Hook
Put on until a click is
heard
Inner cover
How to remove the inner cover
Press the inner cover from the front and rear
sides inward (at the same vertical position as
the hooks) to bend the cover and remove the
cover from the camera.
Press from the front and rear
sides inward to bend
(To be continued reverse page)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
The model number is abbreviated in some descriptions in this manual.
Operating Instructions
Ceiling Mount Bracket
Model No.
WV-Q160C
WV-Q160S
Ns0817-0 PGQX2212ZA Printed in China
Precaution for installation
This product is designed to be used indoors. This product is not operable outdoors.
In order to prevent injury, the product must be securely mounted to a ceiling according to
Installation Guide.
• Make sure that the installation area is strong enough to hold the total weight of the camera assem-
bly (approx. 1.4 k
g
{3.1 lbs.}) before installation.
• The screws that secure the ceiling mount bracket (provided with the camera) in the ceiling are not
supplied. Prepare them according to the material and strength of the area where the product is to
be installed. In this case, wood screws and nails should not be used.
• Do not place this product in the following places.
• Locations where a chemical agent is used such as a swimming pool
• Locations subject to moisture or oil smoke such as a kitchen
• Locations that have a specific environment that is subject to an inflammable atmosphere or sol-
vents
• Locations where a radiation, an X-ray, a strong radio wave or a strong magnetic field is generated
• Locations near coasts directly subjected to sea breezes, or locations subject to corrosive gases
such as from hot springs, volcanic regions, etc.
• Locations where the temperature is not within –10 °C - +50 °C {14 °F - 122 °F}.
• Locations subject to vibrations, such as on vehicles, marine vessels, or above product lines (This
product is not designed for on-vehicle use.)
• Locations where it may get wet from rain or water splash (including under the eaves, etc.)
• Locations subject to moisture or dust
• Locations subject to condensation as the result of severe changes in temperature (In case of
installing the product in such locations, the front cover may become foggy or condensation may
be caused on the cover.)
• The screws and bolts must be tightened with an appropriate tightening torque according to the
material and strength of the installation area. After tightening the screws or bolts, perform visual
check to ensure tightening is enough and there is no backlash.
• The pull-out strength of the installation area shall be 196 N {44 lbf} or more per 1 screw.
2. Mount the camera.
The camera shall be mounted on the camera mounting bracket (supplied with the camera) after
mounting this bracket on a ceiling.
For further information, refer to the Installation Guide of the network camera.