background image

Panasonic

The service technician is required to read and follow the “Safety Precautions” and “Important Safety Notice” in this Manual.

Service Manual

Color Video Projection System

P6

Simplified Manual

Copyright 2001 by Matsushita Electric Corporation of
America. All rights reserved. Unauthorized copying
and distribution is a violation of law.

WARNING! This Service Manual is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this Service Manual by anyone else could result in serious injury or death.” 

Chassis

PT-51D31CE

AP821

PT-61D31CE

AP821

Models

ORDER NO. MTNC010420A1
B2

This Simplified Service Manual is issued to add listed model to the Main Service Manual order No. MTNC010307C1
(PT-51G36E). A full set of schematics, disassembly procedures, and a complete parts list are included in this Simplified
ManualPlease file and use this manual together with Main Service Manual, order No. MTNC010307C1 (PT-51G36E). 

Si

m

pl

ifi

ed

Note: Refer to Technical Guide (P6) for
functional descriptions and Block Diagrams.
(MTNC010308G1).

Summary of Contents for PT-51D31CE



















Reviews: