background image

© 2007 Matsushita Electric Industrial Co., Ltd. All
rights reserved. Unauthorized copying and distribu-
tion is a violation of law.

Order No.VCB0704009CE

Vacuum Cleaner

MC-E3002-WP47

Product Color : White
Destination

: UK

TABLE OF CONTENTS

PAGE

PAGE

1 Specifications

-----------------------------------------------------

2

2 Location of Controls and Components

-------------------

3

3 Troubleshooting Guide

-----------------------------------------

5

4 Disassembly and Assembly Instructions

----------------

6

4.1. BELT (Beater bar belt), BELT B (Motor shaft

belt) ----------------------------------------------------------- 6

4.2. BEATER BAR UNIT--------------------------------------- 7
4.3. IDLER PULLEY UNlT ------------------------------------ 7
4.4. FAN MOTOR UNIT---------------------------------------- 8
4.5. PC board w/component, ON/OFF Switch,

Fuse unit and Power cord (Mains lead)-------------- 9

4.6. ON/OFF SWITCH ----------------------------------------11

5 Wiring Connection Diagram

---------------------------------

11

6 Exploded View and Replacement Parts List

-----------

12

6.1. EXPLODED VIEW (BODY UNIT) --------------------12
6.2. PARTS LIST (BODY UNIT) ----------------------------13

6.3. PACKING INSTRUCTIONS --------------------------- 15
6.4. PACKING LIST ------------------------------------------- 15

Summary of Contents for MC-E3002-WP47
















Reviews: