E
N
G
L
I
S
H
2
CQ-DPX152/DP102U
11
E
N
G
L
I
S
H
1
CQ-DPX152/DP102U
10
Power and Sound Controls
Power
Turn the key in the ignition until the accessory indica-
tor lights.
Power on: Press [SOURCE] (PWR).
Power off: Press [SOURCE] (PWR) again and hold.
Mute
Press [MUTE] to mute the sound completely.
Press [MUTE] again to cancel.
Volume
[
"
VOL]: Up
[
#
VOL]: Down
Press and hold for rapid adjustment.
Volume level (0 to 40)
Anti-volume-blast circuit:
When the power is switched off and on again, the volume slowly rises to the previous level.
The anti-volume-blast circuit will not work when the volume level is set lower than position 20 on the dis-
play.
<
VOL
SEL
BAND
TUNE
MUTE
M/L
1
2
3
4
5
6
7
12
SOURCE
REP
CQ-DPX152U
CD RECEIVER
45W
X
4
LOUD
RANDOM
PWR
8
11
9
10
TRACK
DISP
MONO/LOC
REMOTE
SCAN/APM
<
VOL
SEL
BAND
TUNE
MUTE
M/L
1
2
3
4
5
6
7
12
SOURCE
REP
CQ-DPX152U
CD RECEIVER
45W
X
4
LOUD
RANDOM
PWR
8
11
9
10
TRACK
DISP
MONO/LOC
REMOTE
SCAN/APM
Audio Mode
(Bass/Treble/Balance/Fader)
Regular mode
Volume
Bass
Treble
Balance
Fader
Note:
≥
If no operation takes place for more than 5 seconds
in audio mode (2 seconds in volume mode), the dis-
play returns to the regular mode.
Bass:
Adjustable range:
j
12 to
i
12 (by 3 step)
Treble:
Adjustable range:
j
12 to
i
12 (by 3 step)
Balance:
R (right speaker) or L (left speaker)
Fader:
F (front speaker) or R (rear speaker)
Adjustable range:
Balance center
1 to 15 (by 1 step)
Adjustable range:
Fader center
1 to 15 (by 1 step)
Loudness
(Only for main unit)
Press [LOUD] to enhance bass and treble tones at
low or medium volume.
Press [LOUD] again to cancel.
ACC
ON
Press [SEL] to select the audio mode.
1
Press [
"
VOL] or [
#
VOL] to change each
level.
2
Clock Basics
The 12-hour system is used for the clock.
Hours
2
Press and hold [DISP] (display) for more than
2 seconds.
3
Press [
%
TUNE] or [
$
TUNE].
Minutes
4
Press [DISP] (display).
5
Press [
%
TUNE] or [
$
TUNE].
6
Press [DISP] (display).
Note:
≥
Press and hold [
%
TUNE] or [
$
TUNE] to
change numbers rapidly.
(Hours blink.)
(Hours set.)
(Minutes blink.)
(Minutes set.)
(End.)
Initial Time
1
Press [DISP] (display).
(Clock display.)
Time Reset
Press and hold [DISP] (display) for more than
2 seconds to activate the time setting mode to
reset the time.
Then, repeat steps
3
to
6
.
[DISP] (display)
[
%
TUNE], [
$
TUNE] (Hours, minutes)
MUTE
LOUD
[DISP] (display)
Display Change
Press [DISP] (display) to switch to the clock dis-
play.
When the power is off:
No display
Clock display
