background image

 

 

Page 1 of 17 

Proteus 26 & 26BA 

 

Operating & Maintenance 

Instructions 

 

 

READ THIS MANUAL 

 

This operator's manual has important 
information for the use and safe operation 
of this machine. Read this manual 
carefully before starting the machine. 

 

Keep this manual and tell all operators to 
read this manual. If you do not follow the 
instructions, you can cause an injury or 
damage equipment.

 

Carefully inspect all 

components to ensure that there is no 
concealed freight damage. If damage is 
discovered, file a "CONCEALED 
DAMAGE REPORT" immediately with the 
delivering carrier.

   

The content of this 

manual are based on the latest product 
information available at the time of 
publication. 

Pacific Steamex

 reserves the 

right to make changes or improvements to 
its machines without notice. 

For new manuals write to: 
 

Pacific 

2259 S. Sheridan 

Muskegon, MI  49442-6252 

 

or download the most recent version of 

the manuals from our website:  

 

www.pacificfloorcare.com

 

 

FOR YOUR CONVENIENCE, RECORD THE 
FOLLOWING IMPORTANT INFORMATION: 

SERIAL NUMBER 

DATE PURCHASED 

 

 

Summary of Contents for Proteus 26


















Reviews: