SAFETY INFORMATION
This digital set-top has been manufactured
and tested with your safety in mind.
However, improper use can result in
potential electric shock or fire hazards.
To avoid defeating the safeguards that
have been built into your set-top, please
observe the precautions discussed in this
document.
Warnings on your set-top
The lightning flash with
arrowhead symbol, within a
triangle, is intended to alert you
to the presence of uninsulated
“dangerous” voltages within
your set-top’s enclosure that
may be of sufficient magnitude
to constitute a risk of electric
shock to persons.
The exclamation point within a
triangle is intended to alert you
to the presence of important
instructions in the literature
accompanying your set-top.
Other warnings
To reduce the risk of electric shock, do
not remove the cover of your set-top.
There are no user-serviceable parts inside it.
Do not perform any servicing unless you
are qualified to do so by pace. Refer all
servicing to qualified service personnel.
Servicing the set-top yourself will
invalidate the warranty.
On the rear panel of your set-top there
is a tamper-evident label that states
“Warranty void if broken or removed”.
To reduce the risk of fire or electric shock,
do not expose this set-top to rain or
moisture.
INSTALLATION
The installation of your set-top should
be carried out by a qualified installer and
should conform to local codes.
Note to the installer
This reminder is provided to call the
attention of the cable-TV-system installer
to Section 820-40 of the National
Electrical Code (USA), which provides
guidelines for proper grounding and, in
particular, specifies that the cable ground
shall be connected to the grounding
system of the building, as close to the
point of cable entry as is practical.
In addition to the Important Safety
Instructions, please read the Safety
Information below.
Power sources
You must operate your set-top only
from the type of power source indicated
on the marking label. If you are not
sure of the type of power supply to
your home, consult your dealer or
local power company. If you move your
If you move your
set-top between locations at different
temperatures, allow it to reach room
temperature before you apply power to it.
Overloading
Do not overload wall outlets, extension
cords or other power outlets as this can
result in a risk of fire or electric shock.
Lightning
For added protection for your set-top
during a lightning storm, or when it is left
unattended and unused for long periods
of time, disconnect the cable system from
your set-top. See also item 13 in the
Important Safety Information.
Placement and mounting
Do not place your set-top on an unstable
or uneven surface. Your set-top may fall,
causing serious injury to a child or adult
and serious damage to your set-top. If
you mount your set-top, for example to a
wall or ceiling, follow the manufacturer’s
instructions and use a mounting accessory
recommended by the manufacturer. See
also item 12 in the Important Safety
Instructions.
Risk of fire or scorching
Never place naked flame sources, such
as lighted candles, on or adjacent to your
set-top.
Ambient temperature
The operating temperature range of
your set-top is 32-104°F. If the ambient
temperature around your set-top falls
outside this range, you must correct this in
order for your set-top to work correctly
and safely. For example, if the temperature
is too high, switch on the air conditioning.
Ventilation
Slots and openings in the casing of your
set-top are provided for ventilation, to
ensure reliable operation of your set-top
and to protect it from overheating.
• Never block the ventilation openings
by placing your set-top on a bed, sofa,
rug or other similar surface.
• Never cover the ventilation openings
with items such as newspapers, table-
cloths or curtains.
• Do not place your set-top in a built-
in installation such as a bookcase
or rack unless proper ventilation is
provided or you have adhered to the
manufacturer’s instructions.
• Maintain a minimum distance of 1 inch
around your set-top for sufficient
ventilation.
See also item 7 in the Important Safety
Instructions.
Transporting
Move the combination of set-top and
cart with care. Quick stops, excessive
force and uneven surfaces may cause
the combination of set-top and cart
to overturn. See also item 12 in the
Important Safety Instructions.
Replacement parts
When replacement parts are required,
be sure that the service technician
has used replacement parts specified
by the manufacturer or that have the
same characteristics as the original part.
Unauthorized substitutions may result
in fire, electric shock or other hazards.
See also item 14 in the Important Safety
Instructions.
Safety check
Upon completion of any servicing or
repairs to your set-top, ask the service
technician to perform safety checks to
determine that your set-top is in its
proper operating condition. See also item
14 in the Important Safety Instructions.
Entry of objects and liquids
Never push objects of any kind into
your set-top through openings as they
may touch dangerous voltage points or
short-out parts that could result in fire
or electric shock. Never spill liquid of any
kind on your set-top.
Water and moisture
Do not expose this set-top to dripping
or splashing and ensure that no objects
filled with liquids, such as vases, are placed
on your set-top. See also item 5 in the
Important Safety Instructions.
SAVE THIS INFORMATION FOR
FUTURE REFERENCE
Regulatory
information
CAUTION: Do not attempt to
modify your set-top without written
authorization from the manufacturer.
Unauthorized modification could
void your authority to operate your
set-top.
Epilepsy And
On-screen Images
Certain people are susceptible to epileptic
seizures or losing consciousness when
faced with certain types of flashing lights in
our daily environment.
These people are exposed to the risk of
seizures if they watch certain television
images. This phenomenon may appear even
when the subject has no previous history
of this problem or has never suffered an
epileptic seizure.
If you, or a member of your family, has
already suffered symptoms linked to
epilepsy (seizure or loss of consciousness)
in the presence of stimulation by light,
please consult your doctor before using
this product.
If you or any person using the equipment
experiences dizziness, involuntary
movements or convulsion, please
immediately stop viewing and consult a
doctor.
NOTE
Your set-top has been tested and found
to comply with the limits for a Class B
digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. Your set-top generates,
uses and can radiate radio-frequency
energy and, if not installed and used in
accordance with the instructions, may
cause harmful interference to radio
communications.
However, there is no guarantee
that interference will not occur in a
particular installation. If your set-top
does cause harmful interference to
radio or television reception, which can
be determined by turning your set-top
off and on, you are encouraged to try
to correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving
antenna.
• Increase the separation between
your set-top and the receiver.
• Connect your set-top to an outlet
on a circuit different from that to
which the receiver is connected.
• Consult your dealer or an
experienced radio/TV technician for
help.
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
RISQUE DE CHOC ELECTRIQUE
NE PAS OUVRIR
ATTENTION
IMPORTANT SAFETY INSTRUCTIONS
Before you install or use the apparatus, you must read and understand these
Important Safety Instructions. At all times when using the apparatus you
must follow these Important Safety Instructions to reduce the risk of fire,
electrical shock and injury to persons.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type
plug. A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the
provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the
cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when
unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen
into the apparatus, the apparatus has been exposed to rain or moisture,
does not operate normally, or has been dropped.
Thank you for choosing the Pace DC100X Set-top.
Follow the set-up instructions in this Quick Start Guide to
ensure you get the best from your set-top.
To ensure you use this product safely, please read all the
safety information included in this document.
Quick Start Guide
Pace DC100X
This product incorporates copyright protection technology that is protected by
U.S. patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is intended for home and other
limited pay-per-view uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
Pace and
are trademarks and/or registered trademarks of
Pace Micro Technology plc.
Other trade marks listed herein are the property of their respective owners.
The model number, serial number and electrical rating of this set-top are on a label
on its base.
Copyright © 2007 Pace Micro Technology plc. All rights reserved.
Service address:
Pace Micro Technology (Support
Services) Ltd.,
3701 FAU Boulevard, Suite 200,
Boca Raton, Florida, 33431, U.S.A.
Terms and Conditions for Use of Software (“Terms”)
THE PRODUCT TO WHICH THESE TERMS RELATE (THE “PRODUCT”)
INCORPORATES SOFTWARE WHICH IS OWNED BY PACE MICRO TECHNOLOGY
PLC (“PACE”) OR ITS THIRD PARTY LICENSORS (THE “SOFTWARE”). BEFORE
USING THE PRODUCT PLEASE READ THESE TERMS. IF YOU DO NOT AGREE TO
THESE TERMS YOU MAY NOT USE THE PRODUCT AND SHOULD IMMEDIATELY
RETURN THE PRODUCT TO YOUR SUPPLIER. THESE TERMS ALSO APPLY TO ANY
MODIFICATIONS, UPDATES OR SUPPLEMENTS TO THE SOFTWARE PROVIDED
TO YOU. FOR PURPOSES OF THESE TERMS, “YOU” MEANS YOU, THE END USER,
AND YOUR PRODUCT SUPPLIER, UNLESS THE CONTEXT REQUIRES OTHERWISE.
A. License Grant and Conditions
1. Pace, or your supplier, if applicable, grants you a non-exclusive, non-transferable,
limited license to use the Software solely as integrated with, incorporated into, or
provided for use in connection with the Product.
2. Pace reserves all rights not expressly granted to you under these Terms.
3. You may not transfer any of your limited rights in the Software without the prior
written consent of Pace, and if consent is provided then the Software shall only
be transferred in conjunction with the transfer of the Product AND ONLY IF the
transferee has read and agreed to accept these Terms.
4. You must ensure that the copyright, trademark and other protective notices
contained in the Software are maintained and not altered or removed.
5. The Software is protected by copyright and other laws and international copyright
and other treaties.
6. The Software provided hereunder is licensed (not sold). Pace is NOT transferring
title or any ownership rights in the Software to you.
7. All title and intellectual property rights in and to the Software and all modifications,
updates, enhancements and derivative works of the Software are owned exclusively
by Pace or its licensors and you agree to execute any document reasonably
requested by Pace to evidence such ownership rights.
8. Certain third party software used in connection with the Product may be made
directly available to you by operating system or other third party providers. Use of
such Software is also subject to the terms of any applicable agreement between you
and such third party.
B. License Restrictions
Except as expressly permitted by statute
you may not
:
1. use the Software in conjunction with any other hardware or equipment other than
the Product;
2. copy or modify all or any portion of the Software;
3. incorporate all (or any portion of) the Software into other programs developed
or used by (or on behalf of) you;
4. reverse engineer, decompile, decrypt or disassemble the Software (or any
portion of the Software); or
5. export, transfer or re-export the Software in violation of any applicable law.
C. Termination
These Terms are effective until terminated. You may terminate these Terms by
returning the Product to your supplier. These Terms will terminate automatically
without notice if you fail to comply with these Terms or any other written
agreement between you and Pace. Upon termination you must return the Product
to your supplier.
D. Disclaimer
1. EXCEPT AS SET FORTH IN ANY WRITTEN AGREEMENT BETWEEN
YOU AND PACE (OR YOUR SUPPLIER), THE SOFTWARE IS (TO THE
EXTENT PERMITTED BY LAW) SUPPLIED “AS IS” AND PACE AND
ITS LICENSORS EXPRESSLY EXCLUDE ALL WARRANTIES, EXPRESS
OR IMPLIED, INCLUDING (BUT NOT LIMITED TO) WARRANTIES OF
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR PURPOSE AND
NON-INFRINGEMENT.
2. EXCEPT AS SET FORTH IN ANY WRITTEN AGREEMENT BETWEEN YOU
AND PACE, IN NO CIRCUMSTANCE WILL PACE BE LIABLE FOR ANY
DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, PUNITIVE OR INCIDENTAL
DAMAGE (INCLUDING LOSS OF PROFITS, BUSINESS INTERRUPTION,
LOSS OF DATA OR THE COST OF PROCUREMENT OF SUBSTITUTE
GOODS, TECHNOLOGY OR SERVICES) ARISING OUT OF THE USE OR THE
INABILITY TO USE THE SOFTWARE.
E. General
These Terms are governed by the laws of the State of New York and you may only
bring claims exclusively in New York courts and Pace shall be entitled to bring a
claim in the courts of any jurisdiction. Any failure by Pace to enforce any of its rights
hereunder or applicable law shall not constitute a waiver of such rights. Pace’s
licensors and suppliers shall be third party beneficiaries of this License Agreement,
as applicable.
YOUR USE OF THE PRODUCT CONSTITUTES YOUR ACKNOWLEDGEMENT
THAT YOU HAVE READ THESE TERMS AND AGREE TO BE BOUND HEREBY.
