![background image](http://html.mh-extra.com/html/ott-lite-technology/venice-2599211p/venice-2599211p_manual_1658829001.webp)
ENGLISH
ins 5 0003 rev 1026
CAUTION!
If the external flexible cable or cord of this luminaire is damaged, it shall be exclusively replaced by the manufacturer
or its service agent or a similar qualified person in order to avoid a hazard. Indoor use only.
LAMP ASSEMBLY
1.
Unpack all lamp parts and lay out
on the floor with the base (A)
standing upright.
2.
Thread socket (D) to upper
decorative pole (C) by hand, turning
clockwise until tight.
3.
Fully seat upper decorative pole
(C) into lower decorative pole (A).
Set assembly upright.
4.
Secure decorative pole together
by tightening set screws (B) using
included tool (I), turning clockwise
until tight.
5.
Attach harp (E) to socket brackets
(J) by squeezing open ends of harp,
placing flattened section inside of
brackets (J) and releasing. End by
sliding caps (K) over brackets (J).
6.
Place shade (F) on harp (E).
7.
Place reflector (G) on top of
shade (F), making sure the white side
faces down.
8.
Attach finial (H) to top of harp
(E), turning clockwise until tight.
9.
Install bulb following BULB
INSERTION/ REPLACEMENT
instructions.
10.
Plug the lamp into a standard
120V outlet.
11.
Turn lamp on or off by rotating
switch (L) clockwise.
BULB INSERTION/REPLACEMENT
1.
Make sure the lamp is not
plugged into an electrical socket.
2.
If the lamp has been in use, allow
it to cool for approximately five
minutes before proceeding.
3.
To install a bulb in the socket,
hold the bulb (N) firmly near the
base, align bulb pins with matching
pin-holes then push it straight into
the socket until it "snaps" into place.
4.
To remove a bulb (N) already
installed in the lamp, grasp it firmly
at the base and, using a slight
rocking motion, pull it straight out of
the socket.
Do not twist or turn
the bulb.
Please note that in operation,
OTT-LITE
®
bulbs are not dimmable.
Enjoy your OTT-LITE
®
Venice Floor
Lamp!
This lighting system is designed for
use with OTT-LITE VisionSaver Plus
®
bulbs only (model number
H3400K). Use of other products
voids the warranty and may result
in damage to the lighting system.
CAUTION! IMPORTANT SAFETY INSTRUCTIONS:
THIS PORTABLE LAMP HAS A POLARIZED PLUG (ONE BLADE IS WIDER THAN THE OTHER) AS A FEATURE TO
REDUCE THE RISK OF ELECTRIC SHOCK. THIS PLUG WILL FIT IN A POLARIZED OUTLET ONLY ONE WAY. IF THE
PLUG DOES NOT FIT FULLY IN THE OUTLET, REVERSE THE PLUG. IF IT STILL DOES NOT FIT, CONTACT A QUALIFIED
ELECTRICIAN. NEVER USE WITH AN EXTENSION CORD UNLESS PLUG CAN BE FULLY INSERTED. DO NOT ALTER
THE PLUG.
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.
CAUTION:
BALLAST REQUIRES PROPER VENTILATION FOR PROPER OPERATION. A MINIMUM OF 6
INCHES OF AIR SPACE MUST BE PROVIDED ON ALL SIDES EXCEPT WHERE PLUGGED INTO AN ELECTRICAL OUTLET.
AVERTISSEMENT! IMPORTANTES DIRECTIVES DE
SÉCURITÉ:
CETTE LAMPE PORTATIVE EST MUNIE D'UNE FICHE POLARISÉE (UNE LAME PLUS LARGE QUE
L'AUTRE). CE DISPOSITIF DE SÉCURITÉ DIMINUE LE RISQUE DE CHOCS ÉLECTRIQUES PUISQUE LA FICHE NE
S'INSÈRE DANS LA PRISE QUE D'UN SEUL CÔTÉ. SI ELLE N'ENTRE PAS DANS LA PRISE, INVERSEZ-LA. SI ELLE
N'ENTRE TOUJOURS PAS, CONTACTEZ UN ÉLECTRICIEN QUALIFIÉ. N'UTILISEZ JAMAIS AVEC UNE RALLONGE SAUF
SI LA FICHE S'INSÈRE ENTIÈREMENT. NE MODIFIEZ PAS CE DISPOSITIF DE SÉCURITÉ.
AVERTISSEMENT:
POUR ÉVITER LES CHOCS ÉLECTRIQUE, INSÉREZ LE BOUT LARGE DE LA FICHE
DANS LA GRANDE FENTE ET POUSSEZ JUSQU'AU BOUT.
ATTENTION:
LES BALLASTS NÉCESSITENT UNE VENTILATION ADÉQUATE POUR UN FONCTIONNEMENT
CORRECT. UN MINIMUM DE 15 CM D'ESPACE DOIT ÊTRE LAISSÉ DE CHAQUE COTÉ À L'EXCEPTION DE CELUI OÙ
SE TROUVE LE BRANCHEMENT À LA PRISE D'ALIMENTATION ÉLECTRIQUE.
¡PRECAUCIÓN! INSTRUCCIONES DE SEGURIDAD
IMPORTANTES:
ESTA LÁMPARA PORTÁTIL TIENE UN ENCHUFE POLARIZADO (UNA DE SUS PATAS ES
MÁS ANCHA QUE LA OTRA) COMO CARACTERISTICA PARA REDUCIR EL RIESGO DE UNA DESCARGA ELÉCTRICA.
ESTE ENCHUFE ENCAJARÁ EN CUALQUIER TOMACORRIENTE POLARIZADO SOLO DE UNA MANERA. SI EL ENCHUFE
NO CALZA COMPLETAMENTE EN EL TOMACORRIENTE DÉLE LA VUELTA. SI AÚN NO ENCAJA, PÓNGASE EN
CONTACTO CON UN ELECTRICISTA CALIFICADO. NUNCA UTILICE UNA EXTENSIÓN A NO SER QUE EL ENCHUFE
PUEDA SER TOTALMENTE INSERTADO. NO ALTERE EL ENCHUFE.
PRECAUCIÓN:
PARA PREVENIR UNA DESCARGA ELÉCTRICA, HAGA COINCIDIR LA PATA ANCHA DEL
ENCHUFE CON LA RANURA ANCHA, INSERTE TOTALMENTE.
PRECAUCIÓN:
LA RESISTENCIA NECESITA UNA ADECUADA VENTILACIÓN PARA FUNCIONAR
CORRECTAMENTE. DEBE PROVEERSE UN ESPACIO DE AIRE DE UN MÍNIMO DE 6" EN TODOS LOS LADOS,
EXCEPTO DONDE ESTÁ CONECTADA A UN TOMACORRIENTE.
25W Venice Floor Lamp
25W
Venice Floor Lamp
2599211P