background image

WARNING

Compact Series

MODEL

 

OD

C-1008 | ODC-8003

PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.

 

Electrical products can cause death or injury, or damage to property.
If in any doubt about the installation or

 

use of this product, consult a competent electrician.

CLEANING & MAINTENANCE

WARNING — THE INSTALLATION MUST BE CARRIED OUT BY

A QUALIFIED

 

ELECTRICIAN. 

1. For general ventilating use only. DO NOT use to exhaust hazardous or explosive

materials and vapours

2. To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray,

construction dust, etc. off power unit

3. Read specification label on product for further information and requirements

Instruction Manual

1-888-543-6473
1-888-541-6474

13376 Comber Way 

Surrey BC V3W 5V9

[email protected] 
www.ortechindustries.com

375 Admiral Blvd

 

Missis

s

auga

ON L5T 2N1

Application Notice

1.

Use this unit only in the manner intended by the manufacturer. Contact the manufacturer in case of questions

2.

Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being

switch

ed

 on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device,

such as a tag, to the service panel

3.

Installation work and electrical wiring must be done by a qualified person(s) in accordance with all applicable codes and standards,

including fire-rated construction codes and standards

4.

Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent

 

back drafting. Follow the heating equipment manufacturer's guideline and safety standards such as those published by the National Fire

Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE),

and the local code authorities

5.

When cutting or drilling into wall or ceiling, DO NOT damage electrical wiring and other hidden utilities

6.

Ducted fans must always be vented to the outdoors

7.

Acceptable for use over a tub or shower when connected to a GFCI (Ground Fault Circuit Interrupter) —

protected branch circuit (ceiling installation only)

8.

This unit must be grounded

9.

This product is designed for installation in ceilings up to a 12/12 pitch (45°). Duct connector MUST point up.

DO NOT mount this product in a wall

CAUTION

For quiet and efficient operation, long life, and attractive appearance — lower or remove grille and vacuum interior of unit 
with the dusting brush attachment.
The motor is permanently lubricated and never needs oiling.

 If the motor bearings are making excessive or unusual noises, 

replace the motor with the exact service motor. The impeller should also be replaced.

OPERATION

See "Connect Electrical Wiring" on page 

4

 of this instruction manual

 for details

.

INSTALLATION GUIDE

Types of Typical Installations

1.

Housing mounted to I-joists (refer to Assembly Instructions 

1 on the next page of this manual)

2.

Housing mounted to joists

 (refer to Assembly Instructions 1 on the next page of this manual)

3.

Housing mounted to truss

 (refer to Assembly Instructions 2 on the next page of this manual)

CAUTION

Summary of Contents for ODC-1008

Page 1: ...fficient air is needed for proper combustion and exhausting of gases through the flue chimney of fuel burning equipment to prevent back drafting Follow the heating equipment manufacturer s guideline and safety standards such as those published by the National Fire Protection Association NFPA and the American Society for Heating Refrigeration and Air Conditioning Engineers ASHRAE and the local code...

Page 2: ...mounting flange 2 Mount with Mounting Holes and Hanger Bar a Slide one hanger bar into the channel on the housing and adjust as needed to fit between framing b Hold housing in place so that the housing contact the bottom of the joist Screw housing to joist through the hole of the housing c Screw the hanger bar onto the other side of joist through the hole d Screw hanger bar to housing with screw e...

Page 3: ...ce and avoid installing the fan with smaller ducts than recommended Insulation around the ducts can reduce energy loss and inhibit mold growth Fans installed with existing ducts may not achieve their rated airflow Retrofit Installation a Mount with additional mounting holes The interior of the fan housing contains additional mounting holes in case exterior mounting is not possible Screw or nail th...

Page 4: ...he wires as shown Install Grille Install ceiling material to complete the ceiling construction Then cut around the fan housing To attach the grille assembly to the fan housing pinch the grille springs on the sides of the grille assembly and position the grille into the housing with the grille springs in the appropriate slots Push the grille assembly towards the ceiling to secure Service Parts Blow...

Reviews: