background image

 

ISOLDE

 

 

USER GUIDE 

 

Congratulations on your new CONSONANCE! 
 
Opera Audio products are based on a simple philosophy: 
 
The component shall reproduce the original musical sound, purely and naturally. 
 
The products are easy to operate and are manufactured according to the best quality 
principles. 
 
All  CONSONANCE  products  are  created  with  acoustical  instruments  in  a  concert 
situation as point of reference. The music is reproduced exactly like the original and is 
limited only by the quality of the recording. 
 

Our aim is to give you the best possible music experience! 

 
 
 

CONTENTS 

1. ISOLDE Turntable 

1)    ISOLED Part list                                  

 

 

 

                                    p.2 

2)    ISOLED Assembling the Turntable   

 

                                                  p.3 

3)    ISOLED Turntable Technical specifications                                                    p.5 

                   

2. T8 Tonearm 

1)    T8 Part list                                                                                                            p.6 
2)    T8 Tone arm mounting                                                                                        p.7       
3)    T8 Tone arm Technical specifications                                                              p.9 

 

3. Warranty         

                                                                                           

 

  p.10

 

 
 
 
 
 
 
 

Summary of Contents for Consonance Isolde











Reviews: