INDUSTRIAL FAN HEATERS
Output:
5
Kw
, 9
Kw, 15Kw
3 HEAT SETTINGS
M
odel
Nos:
Olympus JetHeat
OLY-J5/3,
OLY-J9/3
,
OLY-J15/3
1.2. GENERAL SAFETY
1.2.1. MAINTENANCE PRECAUTIONS
WARNING!
Disconnect the heater from the mains power
1.2.2. POSITIONING OF HEATER
WARNING! DO NOT
use the heater near flammable material
liquids, solids, gases or compressed gas cylinders etc.
DO NOT
place the heater close to a bath, wash basin, shower,
swimming pool or any other water-filled area or wet surface.
DO NOT
place the heater up against any surface such as a
wall, door or furniture etc.
DO NOT
place the heater immediately below any electrical
outlet.
Position the heater at least a minimum of 0.5mtr at the rear
and sides, and 2mtr at the front, from any walls or objects.
DO NOT
place the heater on a raised surface or anywhere
where it could topple over.
Original Language UK English
1.1. ELECTRICAL SAFETY
WARNING!
ELECTRICAL INSTALLATION OF THE HEATER
TO A 3-PHASE 415
VOLT SUPPLY MUST ONLY BE
CARRIED OUT BY A QUALIFIED ELECTRICIAN.
Make sure the power supply cable is correctly connected
to the earth. It is the user’s responsibility to read,
understand and comply with the following:
You must check all electrical equipment and appliances to
ensure they are safe before using. You must inspect power
supply leads, plugs and all electrical connections for wear and
damage. You must ensure the risk of electric shock is
minimised by the installation of appropriate safety devices. An
RCCB (Residual Current Circuit Breaker) should be
incorporated in the main distribution board.
You must
also read
and understand the following instructions concerning electrical
safety.
1.1.1. The
Electricity At Work Act 1989
requires all portable
electrical appliances, if used on business premises, to be tested
by a qualified electrician, using a Portable Appliance Tester
(PAT), at least once a year.
1.1.2. The
Health & Safety at Work Act 1974
makes owners of
electrical appliances responsible for the safe condition of the
appliance and the safety of the appliance operator.
If in any
doubt about electrical safety, contact a qualified electrician.
1.1.3. Ensure insulation on all cables and the product itself is safe
before connecting to mains power supply.
1.1.4. Ensure that cables are always protected against short circuit
and overload.
1.1.5. Regularly inspect power
supply, leads, plugs and all
electrical connections for
wear and damage,
especially power
connections, to ensure that
none are loose.
1.1.6.
Important:
Ensure the
voltage marked on the
product is the same as the
electrical power supply to
be used. A three phase
plug must be fitted to this
1.1.7.
DO NOT
pull the powered appliance by the power cable.
1.1.8.
DO NOT
pull power plugs from sockets by the power cable.
1.1.9.
DO NOT
use worn or damage leads, plugs or connections.
Immediately replace or have repaired by a qualified electrician.
1.1.10.
This product must be fitted with a 3-phase plug according
to the diagram, and will require a minimum of 16Amps per
phase for
OLY-J5/3
and
OLY-J9/3
,
the
OLY-J15/3
is
32Amps for
the 15Kw.
You
must contact a qualified electrician
t
o ensure
an appropriately fused supply is available.
Connect GREEN/
YELLOW wire to earth (E)
terminal. Connect the live wires
to live 1, 2 and 3. When completed, check that there are no
bare wires, that all wires have been connected correctly, that
the cable external insulation extends beyond the cable
restraint and that the
cable
restraint is tight.
1. SAFETY
IMPORTANT:
PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT
CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL
INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE.
Refer to
Instructions
Indoor Use
Only
Olympus OLY-JetHeat | Issue 2) 17/08/16
OLY-J15/3
OLY-J5/3
OLYJ9/3
Thank you for purchasing a Olympus Industrial Appliances JetHeat product. Manufactured to a high standard, this product will, if used
according to these instructions and maintained properly, give you years of trouble free performance
.
© Olympus Industrial Appliances UK
appliance.
supply before servicing or performing any maintenance.
Servicing or maintenance must only be carried out by an
authorised service agent.
Check that the heater is in sound condition and good working
order. Take immediate action to repair or replace damaged
parts.
Use recommended parts only. Unapproved parts may be
dangerous and will invalidate the warranty.
DO NOT
attempt to repair a damaged heater, contact an
authorised service agent.
MANUAL FOR
