background image

Complete Teardown, Cleaning/Lubrication, and Reassembly of the Olympus BH2-CH Substage Assembly   

Revision 1      Page 1 of 26 

 

Complete Teardown, Cleaning/Lubrication, 

and Reassembly of the Olympus 

BH2-CH Substage Assembly 

Revision 1 

 

Copyright © 2017 Carl Hunsinger 

All  rights  reserved.    This  document  may  not  be  reproduced  or  distributed,  in  whole  or  in  part,  for  any 
commercial purpose without the express written consent of the author ([email protected]).   Permission is 
hereby  granted  to  distribute  this  PDF  document  in  its  entirety  for  personal,  non-commercial  purposes  only, 
provided that the contents are not modified in any way, including the copyright notices contained herein.  This 
document may be freely distributed on WWW, FTP, or BBS sites in accordance with these restrictions.   

The  content  of  this  document  is  provided  for  informational  purposes  only,  with  no  expressed  or  implied 
warranties whatsoever, including, but not limited to, function, suitability, safety, accuracy, or completeness of 
information. 

Revision History 

Revision 

Description of Changes 

Date 

Initial Release 

August 13, 2017 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Summary of Contents for BH2-CH Substage



























Reviews: