Page 1 from 5
SOUNDER WITH BEACON FOR FIRE DETECTION PANEL
GENERAL
This device is Visual Alarm Devices (VAD) for
fire detection panels that offer a strong sound
output and an optical warning with a beacon
and is used on ships. The strong sound and
the optical warning beacon cover many
square metres.
It features two inputs (N1, N2)
for the production of two different sounds.
This device can co-operate with any fire
detection panel (BSR-2104/MAR, BSR-
2114/MAR, BS-1632, BS-1634, BS-1636, BS-
636).
Installation and Connection
1.
First, remove the retaining screw, place a
flat blade screwdriver in the holes of the
plastic hooks and remove the plastic cover
(Image 1 on page 2).
2.
Remove carefully the beacon connector
(Image 2 on page 2).
3.
Use the supplied mounting parts to install the
siren’s base at a height of 2.4 metres from
the floor (figure 1 on page 2). Place the
plastic plugs and fasten the screws to the
mounting holes
.
Attention!! Make sure that
the siren’s base is installed upwards
as
shown in figure on page 4.
4.
Place the caps and make a hole in the center
using a small screwdriver.
Pass through the
caps the cables to connect the device.
5.
The (
+N1
or the
+N2
)
terminal block
is
connected to the
(
+
)
output of
Alarm-1
or
Alarm-2
of the panel and the (
-
)
of the
terminal block is connected to the
(
-
)
out
put
of
Alarm-1
or
Alarm-2
of the panel.
Accordingly connect in parallel all the sirens.
(The maximum number of sirens depends on
the type of the panel).
6
.
To select various
sound effects
use the
dipswitch 1,
2
and
3 and
choose the
diserable sound effect,
according to
tables 2
and 3 on page 3.
7
.
For
LED effect
variation use the dipswitch 4
(Table 1) on page 2. On the last siren of the
line, we must connect in parallel with its
power cables, the terminal resistor that was
removed from the alarm contacts of the
panel.
8.
Reinstall the beacon connector (step 2).
Refit the plastic cover until the plastic hooks
are securely attached (step 1) and fasten the
retaining screw (torque 0.6Nm). Attention!!
Make sure that the siren’s cover is installed
in the correct orientation.
9.
Test the device after installation.
Β
S-531
/1
/MAR
ΤΕCHNICAL CHARACTERISTICS
OPERATION VOLTAGE
MAXIMUM CONSUMPTION
MAXIMUM SOUND OUTPUT in1m
ΤYPE OF APPLICATION ENVIRONMENT
MOUNTING
COVERAGE (y)
BEACON
21-28V DC
Τ
ype
Α
1 Power LED
Wall
6 m around the siren at an angle of 180°
94dB (sound effect 1
)
1.2W
OPERATION TEMPERATURE RANGE
RELATIVE HUMIDITY
EXTERNAL DIMENSIONS
TYPICAL WEIGHT
GUARANTEE
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
IP 42C
COVERAGE VOLUME
FLASH RATE
FLASH COLOUR
86.4m³
(max)
1 Hz (Switchable to 0.5 Hz)
Red
o
0 to 60 C
Up to 95%
2 years
230gr.
141 x 141 x 100 mm
CONSTRUCTION MATERIAL
Bayblend FR3010
,
transparent
polycarbonate
MOUNTING HEIGHT (x)
2.4m max
COVERAGE VOLUME CODE
W-2.4-6
921531009_09_0
0
4
Thank you for your trust in our products
Olympia Electronics - European manufacturer
rd
EN 54-3:2001+A1:2002+A2:2006, EN 54-23:2010, EN 50130-4:2011, IEC 60092-504
3
Ed.:2001+Cor1:2011, IEC 60533:1999 Edition 2.0
