1 of 7
OASIS
®
VERSACOOLER
®
II MODELS
PG8ACSL, PG8ACSLTM, PG8ACSLTT, PGV8ACSL, PGF8ACSL, PGF8ACSLTM, PGF8ACSLTT, PGVF8ACSL
SUNROC MODELS ADA8ACB, ADAV8ACB, ADAACB, ADAF8ACB, ADAVF8AC, ADAFACB
INSTRUCTIONS
A.
INSPECTION
Inspect the water cooler, water fountain and cartons for evidence of rough handling and concealed damage. Damage
claims should be filed with the carrier.
B.
TO PUT WATER COOLER AND FOUNTAIN INTO SERVICE
1.
NOTE: The following states require a licensed plumber to install cooler; AG, GA, MA, MI, OK, RI, SC, SD, TX, VT
and WI.
CA, KS, MN, NM and OR allow for a state-registered installer or contractor as well. State and local plumbing codes
may prohibit use of saddle tapping valves for water line connection in some applications. All connections must
conform to applicable plumbing codes.
2.
The PG8ACSL is composed of a water cooler and a water fountain. The water cooler contains the refrigeration system
and is always mounted on the right side. This unit can be configured with the water cooler high or low. Refer to
proper roughing in drawing for location of plumbing and electrical service. Filter units have additional instructions on
a label inside fountain side access panel. Read these before installing unit. This drinking water cooler is designed to
be operated at a water supply line pressure of up to 100 psi (690 kPa). A pressure regulator must be installed in
front of the unit’s water inlet if the water pressure (including any possible pressure spikes) could exceed 100 psi
(690 kPa).
3.
FLUSH BUILDING WATER SUPPLY BEFORE INSTALLING UNIT.
4.
Install wall hangers as shown on the desired roughing in drawing. Wall hangers are shipped fastened to the backs of
each unit.
5.
To configure this cooler for right side high or right side low installation, refer to details on page 3. Bottom
screws of the appropriate side panel may be temporarily removed to install patch plate. Assemble drains,
matching the position of the gaskets to the contour of the cooler tops. When used with a bottle filler, the unit
must be configured as a right side high installation.
6.
For refrigerated units, mount the water cooler on the right hanger.
7.
For non-refrigerated units:
a.
TM Models employing touch free sensor and mechanical push button – fountain with the touch free sensor must
be mounted on left side.
b.
TT Models employing touch free sensor on both units – fountain supplied with power cord attached must be
mounted on right side.
8.
On TT models, prior to mounting water fountain on left hanger route the loose 2 pin connector of power cord
from the right-side unit through the open panels and connect into power supply adapter on the shelf inside the
left side water fountain. Refer to details on page 4.
9.
Mount water fountain on left side hanger while routing “Water In” tube through access hole to stop valve as required.
Remove cap from “Drain/Remote Cold Water” connection and insert “Water In” tube.
10.
All provided waste drain parts for field installation are packed in the water fountain. Assemble drain per
appropriate roughing in drawing. The short leg of the crossover piece will be on the water cooler side. When
unit has an internal waste trap, it should be wrapped with insulating tape to prevent sweating. Use of 1-3/4”
knockout for a waste line is not recommended because of potential conflict with ADA* toe space requirements.
Check with your local building code inspector for approval.
11.
Install a shut off valve in water supply line. An in-line strainer is furnished in “Water Supply” tube. Connect “Water
Supply” tube to shut off valve. This connection should not be a solder joint or flare connection to allow access to the
strainer service. To ease removal of the strainer, a sheet metal screw may be lightly threaded into the open end.
12.
Rotate fan blade by hand to see that it is free of obstructions.
13.
Check available power supply against water cooler data plate to ensure correct electrical service. This drinking water
cooler is intended to be connected to a 20A minimum ground fault circuit interrupting (GFCI) device to meet UL
