background image

MODELS  QTRN080 • QTRN110  

Page 1

WARNING  

  

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR IN-

JURY TO PERSONS, OBSERVE THE FOLLOWING:

1.  Use this unit only in the manner intended by the manufacturer. 

If you have questions, contact the manufacturer at the address 

or telephone number listed in the warranty.

2.  Before servicing or cleaning unit, switch power off at service 

panel and lock the service disconnecting means to prevent 

power from being switched on accidentally. When the service 

disconnecting  means  cannot  be  locked,  securely  fasten  a 

prominent warning device, such as a tag, to the service panel.

3.  Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4.  Sufficient air is needed for proper combustion and exhausting 

of  gases  through the  flue  (chimney)  of  fuel  burning  equip-

ment to prevent backdrafting. Follow the heating equipment 

manufacturer’s guideline and safety standards such as those 

published by the National Fire Protection Association (NFPA), 

and the American Society for Heating, Refrigeration and Air 

Conditioning Engineers (ASHRAE), and the local code authori-

ties.

5.  When  cutting  or  drilling  into  wall  or  ceiling,  do  not  damage 

electrical wiring and other hidden utilities.

6.  Ducted fans must always be vented to the outdoors.
7.  Acceptable for use over a tub or shower when connected to 

a GFCI (Ground Fault Circuit Interrupter) - protected branch 

circuit (ceiling installation only).

8.  This unit must be grounded.

CAUTION  

1.  For general ventilating use only. Do not use to exhaust hazard-

ous or explosive materials and vapors.

2.  This  product  is  designed  for  installation  in  ceilings  up  to  a 

12/12 pitch (45 degree angle). Duct connector must point up. 

DO NOT MOUNT THIS PRODUCT IN A WALL.

3.  To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. off power 

unit.

4.  Please read specification label on product for further informa-

tion and requirements.

QTRN SERIES
ULTRA SILENT

 

TM

 FANS

READ AND SAVE THESE INSTRUCTIONS

WARRANTY

Installer: Leave this manual with the homeowner.

OPERATION

Use an on/off switch or solid-state speed control to operate this 
ventilator. See “Connect Wiring” for details.

To register this product visit:

www.nutone.com

NUTONE THREE YEAR LIMITED WARRANTY

NuTone warrants to the original consumer purchaser of its products that 

such products will be free from defects in materials or workmanship for 

a period of three years from the date of original purchase. THERE ARE 

NO OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT 

NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY OR 

FITNESS FOR A PARTICULAR PURPOSE.
During this three-year period, NuTone will, at its option, repair or replace, 

without charge, any product or part which is found to be defective under 

normal use and service.
THIS  WARRANTY  DOES  NOT  EXTEND TO  FLUORESCENT  LAMP 

STARTERS AND TUBES. This warranty does not cover (a) normal main-

tenance and service or (b) any products or parts which have been subject 

to misuse, negligence, accident, improper maintenance or repair (other 

than by NuTone), faulty installation or installation contrary to recommended 

installation instructions.
The duration of an implied warranty is limited to the three-year period as 

specified  for  the  express  warranty.  Some  states  do  not  allow  limitation 

on how long an implied warranty lasts, so the above limitation may not 

apply to you.
NUTONE’S OBLIGATION TO REPAIR OR REPLACE, AT NUTONE’S OP-

TION, SHALL BE THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY 

UNDER THIS WARRANTY. NUTONE SHALL NOT BE LIABLE FOR INCI-

DENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES ARISING OUT OF 

OR IN CONNECTION WITH PRODUCT USE OR PERFORMANCE. Some 

states do not allow the exclusion or limitation of incidental or consequential 

damages, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may also have other 

rights, which vary from state to state. This warranty supersedes all prior 

warranties.
To qualify for warranty service, you must (a) notify NuTone at the address 

or telephone number stated below, (b) give the model number and part 

identification and (c) describe the nature of any defect in the product or 

part. At the time of requesting warranty service, you must present evidence 

of the original purchase date.
Broan-NuTone LLC    Hartford, Wisconsin 

www.nutone.com    888-336-3948

CLEANING & MAINTENANCE

For quiet and efficient operation, long life, and attractive appear-

ance - lower or remove grille and vacuum interior of unit with the 

dusting brush attachment.
The motor is permanently lubricated and never needs oiling. If the 

motor bearings are making excessive or unusual noises, replace 

the blower assembly (includes motor and impeller).

Summary of Contents for ULTRA SILENT QTRN080









Reviews: