background image

M157310C

Installation, Operation, and Maintenance Manual

HOT WATER PRESSURE WASHER

Cleans dirty surfaces with high
pressure hot water.

To the Owner:

Thank you for purchasing a NorthStar hot water pressure washer.  Your machine is designed for long life,
dependability and the top performance you demand!  Take time now  to read through this manual so you better
understand the machine’s operation, maintenance and safety precautions.  Everyone w ho  operates  this machine
must read and understand this manual.  The time you take now w ill  prolong your machine’s life and prepare you
for its safe operation.  Enj oy the exceptional performance of your NorthStar hot water pressure washer, the
industry leader! The manufacturer reserves the right to make improvements in design and/or  changes  in
specifications at any time w ithout incurring any obligation to install them on units prev iously sold.

Quick Facts

Engine Oil

Engine is shipped without oil.  Fill before starting.
Use SAE 10W-30 motor oil.

Pump Oil

Pump is shipped with oil.  Remove shipping tape and check pump oil level before
starting.  Use SAE 30 Non-detergent pump oil (item # 4043) or Cat Pump Oil (item
#22158) for oil changes.

Water

Make sure your water flow is 20% higher than the pressure washer’s flow rate.
Make sure your water is clean and particle free.

Storage

Do not allow water to freeze in the pump, hose, coil, or spray gun.

Spraying
Chemicals

Use any NorthStar brand or equivalent pressure washer chemicals.
Adjust soap adjustment knob to regulate cleaning power.

Maintenance
Schedule

Engine:

Oil: change after first 20 hours, then annually or every 100 hours.
Spark Plug: clean every 100 hours, replace annually or every 300 hours.
Air Filter: clean every 100 hours, replace annually or every 300 hours.

Pump:

Oil: change after first 40 hours, then every 3 months or 500 hours.

Read and understand all manuals before operating.

Any Questions, Comments, Problems or Parts Orders

In the United States

In the United Kingdom

Northstar Customer Service

Call  02392639752

Call 1-800-270-0810

Northern Tool and Equipment Co. (UK) Ltd.

Hours: Monday - Friday 7:00 AM to 5:30 PM

Unit 2, Keel Close,

Saturday 7:30 AM-11:30 AM Central Time

Portsmouth, Hants PO3 5QD, England

  

ITEM NUMBER:    157310

                  

SERIAL NUMBER:

                            

Engine Mo del:                                                               
Pump Mo del:                                                                 
Flow:                                   

Pressure:                              

Hose Length:                      

Lance Lengt h:                      

Nozzle Size:                       

Summary of Contents for M157310C
























Reviews: