1
WS15Z-1 WALL MOUNTED SWITCH
The GoControl™ family of Z-Wave® certifi ed wireless lighting products
(smart LED fi xtures, bulbs, switches, dimmers, outlets, plug-in modules, and
thermostats) and security devices (alert sounder, motion sensor, and door/
window sensor) bring a new level of intelligent wireless capability to commercial
and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote
home automation, security and other applications. This product can be included
and operated in any Z-Wave network with other Z-Wave certifi ed devices
from other manufacturers and/or other applications. All non-battery operated
nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
GoControl Z-Wave products are easy to install, are Z-Wave certifi ed, and allow
dealers to create an integrated wireless network with nearly limitless expansion
and interoperability with security, energy management, home entertainment,
appliances, and more.
DANGER! SHOCK HAZARD.
Read and understand these instructions before
installing. This device is intended for installation in accordance with the National
Electric code and local regulations in the United States, or the Canadian
Electrical Code and local regulations in Canada. It is recommended that a
qualifi ed electrician perform this installation. Make sure the load controlled by
the switch does not exceed 1800 watts. For indoor use only. Retain instructions
for future use.
INSTALLATION
Wire this switch in place of a current wall switch according to the diagram
above. When used, WS15Z-1’s are required to be
wired to the same line (or
neutral)
which is also wired to the load being controlled, and not wired to any
other neutral. If multiple neutrals are tied together in one box, separate the
neutrals to preserve the integrity of the WS15Z-1 circuit.
✓
CAUTION!
Do not wire unit “live” (with power on the circuit).
Adding to a network:
Refer to your Controller operating instructions to add this switch under the
command of the Wireless Controller.
1.
With your Controller in Discovery or Add Mode, tap the switch once for
Network Wide Inclusion. Tap twice for Standard Inclusion.
2.
You should see an indication on your Controller that the “device was added”
to the network and the LED will stop blinking.
3.
The device will appear in the list of Switches. It should display as a switch.
If the Controller/Gateway shows the addition failed, repeat Steps 1-3.
Removing from a network:
The WS15Z-1 can be removed from the network by the Controller/Gateway.
Refer to the Controller operating instructions for details.
1.
Set the Controller into Removal Mode and follow its instruction to delete the
WS15Z-1 from the Controller.
2.
Remove the switch by tapping the paddle 2 times.
3.
You should see an indication on your Controller that the “device was
removed” from the network.
BASIC OPERATION
(Local Control)
The switch paddle on the WS15Z-1 allows the user to:
• Turn the attached load on or off.
• Tapping top of switch turns the load attached ON.
• Tapping bottom of switch turns the load attached OFF.
LED Indication
To act as a night light, the LED on the WS15Z-1 will turn ON when the load
attached is OFF. However, the LED can be user confi gured to turn ON, when
the load attached is ON, if so desired. See “CONFIGURATION” section.
Remote Control
The WS15Z-1 will respond to BASIC and BINARY commands that are part of
the Z-Wave system. Refer to your Controller’s instructions as to whether your
Controller can transmit those commands.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,WS15Z-1, GO CONTROL; P/N: 10008577 X5; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2
WS15Z-1
Z-Wave Radio Frequency (RF) Controlled, 120 VAC
Scene and NWI Capable, Wall Mounted Switch, Series 300
NEUTRAL
120 VAC
PUSH ON
WHITE
LINE
BLACK
PUSH OFF
STATUS LED
GREEN GROUND
TAP TOP OR BOTTOM
OF SWITCH PADDLE
TO CONFIGURE
SCORED TAB WILL
BREAK FLUSH WITH
EDGE OF PLASTIC
BLUE
LOAD
15 AMPS
MAXIMUM
WS15Z-1 AND THE LOAD
MUST SHARE THE SAME
PROPRIETARY NEUTRAL
Shown with supplied
decorative trim plate
NOTE:
This unit must be added to the Network
only where it will be permanently installed.
The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this unit, then install.
