1
FS20Z-1 DUPLEX RECEPTACLE
The GoControl™ family of Z-Wave® certifi ed wireless lighting products
(smart LED fi xtures, bulbs, switches, dimmers, outlets, plug-in modules, and
thermostats) and security devices (alert sounder, motion sensor, and door/
window sensor) bring a new level of intelligent wireless capability to commercial
and residential environments.
The Z-Wave wireless protocol is an international wireless standard for remote
home automation, security and other applications. This product can be included
and operated in any Z-Wave network with other Z-Wave certifi ed devices
from other manufacturers and/or other applications. All non-battery operated
nodes within the network will act as repeaters regardless of vendor to increase
reliability of the network.
GoControl Z-Wave products are easy to install, are Z-Wave certifi ed, and allow
dealers to create an integrated wireless network with nearly limitless expansion
and interoperability with security, energy management, home entertainment,
appliances, and more.
DANGER! SHOCK HAZARD.
Read and understand these
instructions before installing. This device is intended for installation in
accordance with the National Electric code and local regulations in the United
States, or the Canadian Electrical Code and local regulations in Canada. It is
recommended that a qualifi ed electrician perform this installation. Make sure
the total load controlled does not exceed 20 amps.
For indoor use only. Retain instructions for future use.
INSTALLATION
Wire this module in series with a 20 amp (maximum) load according to one
of the diagrams above. The FS20Z-1 has an isolated relay output on the two
BLUE wires. BLACK is for the 120 VAC Line. WHITE is for the 120 VAC Neutral.
With dry contact wiring, the load is powered by a separate source. With wet
contact wiring, the load is powered from the same source as the FS20Z-1.
Fixture Mounted Confi guration
Push the button on the face to confi gure the module to operate from the
Wireless Controller. With the Wireless Controller, the FS20Z-1 can be switched
ON and OFF remotely, and can be included in groups of lights that operate at
the same time (a group can also be a single module), and in scenes that set
a lighting mood.
Other Functions
The button on the FS20Z-1 also plays a role as a reset in addition to including
the module in groups and scenes. This is described in more detail in the
Wireless Controller instructions.
Over-current Protection
The FS20Z-1 is protected by an internal fuse. This internal fuse is factory
serviceable only. Check the home circuit breakers before concluding that the
product must be returned.
Adding to a network:
See the Wireless Controller operating instructions for details to include this
module under the command of the Wireless Controller.
1.
Prepare the Controller to include a unit to the network, by adding it to a group
(method of adding a node to the network). Refer to Controller instructions.
2.
The FS20Z-1 must be in its permanently installed location. Press the button
on the FS20Z-1 once.
3.
You should see an indication on your Controller that the “DEVICE WAS
INCLUDED” in the network.
✓
NOTE: If you have trouble adding the FS20Z-1 to a group it may be that the
Home ID and Node ID were not cleared from it after testing. You must fi rst
“RESET UNIT” with your controller to remove it from the network. Although
adding it to a group includes it in the network, removing it from a group does
not remove it from the network. If removed from a group, it functions only
as a repeater.
Removing from a network:
The FS20Z-1 can be removed from the network by the Controller/Gateway.
Refer to the Controller operating instructions for details.
1.
Set the Controller into Removal Mode and follow its instruction to delete the
FS20Z-1 from the Controller.
2.
Remove the module by tapping the button three times, then press and hold.
3.
You should see an indication on your Controller that the “device was
removed” from the network.
BASIC OPERATION
Button (Local Control)
For testing, the button on the FS20Z-1 allows the installer to turn the load ON
or OFF.
• Tapping button toggles the load attached ON or OFF.
• Also used to include or exclude the module from the Z-Wave system.
When a Controller prompts to “Send Node ID” or to “Press Button on Unit”,
quickly tap the button once to satisfy those instructions. (Tapping the button
also toggles the load attached ON or OFF.)
Remote Control
The FS20Z-1 will respond to BASIC, BINARY, and SCENE commands that are
part of the Z-Wave system. Refer to your Controller’s instructions as to whether
your Controller can transmit those commands.
PRINTER’S INSTRUCTIONS:
INSTR,INSTL,FS20Z-1,GO CONTROL; P/N: 10008918 X3; INK: BLACK; MATERIAL: 20# MEAD BOND; SIZE: 8.500” x 11.000”; TOLERANCE ± .125”; SCALE: 1-1; PAGE 1 OF 2
FS20Z-1
Z-Wave Radio Frequency (RF) Controlled, 120 VAC
Scene Capable, Isolated Contact Fixture Module, Series 300
NOTE:
This unit must be added to the Network
only where it will be permanently installed.
The proper operation of this node in the
mesh network is dependent on it knowing its location with respect to other nodes. You cannot “test bench” confi gure this unit, then install.
P1753
3B54M
FS20Z-1
Fixture Module Receiver
Series 300,
Rel. 5.41
S/N
120 Volts A
C, 60 Hz 908.42 MHz
Isolated Output Contact Ratings (UL/CUR)
277V
AC, 5540W (max), 20 Amp
, Resistiv
e 120/240V
AC
1/2 HP Motor
, 120V
AC, 960W Incandescent Load
WARNING:
Do not e
xceed electr
ical ratings
.
FCC ID:
QIE0791-01
Canada IC:
4436A-079101
Linear LLC
, Car
lsbad, CA
BLK: Line
, WHITE:
Neutr
al,
BLUE:
Load, GRN:
Ground
STATUS LED
PUSH BUTTON TO
ADD NODE TO NETWORK
GREEN
GROUND
NEUTRAL
WHITE
120 VAC
FS20Z-1
LINE
BLACK
BLUE
BLUE
DRY CONTACT WIRING
LOAD IS POWERED FROM
AN ISOLATED SUPPLY
LOAD
20 AMPS
MAXIMUM
LOAD POWER
SOURCE
24 TO 277 VOLTS
STATUS LED
PUSH BUTTON TO
ADD NODE TO NETWORK
GREEN
GROUND
NEUTRAL
WHITE
WHITE
120 VAC
LINE
BLACK
BLUE
BLUE
WET CONTACT WIRING
LOAD IS POWERED FROM
THE SAME SUPPLY AS FS20Z-1
LOAD
20 AMPS
MAXIMUM
FS20Z-1
http://waterheatertimer.org/Control-water-heater-with-z-wave.html
