Nokia 6125 RM-178 Service Manual Download

Page: 1 / 42

Training and Vendor Development

CMO Service Operations

Multimedia Creation & Support

CONFIDENTIAL

15.Dec.2006

Service Manual 6125 RM-178 /6136 RM-106/-199

Approved 4.0

MGR

Page

(42)

RM-178

Transceiver characteristics:

Band:

Quad-band phone for GSM/EDGE 850/900/1800/1900MHz

Camera:

Integrated 1.3-megapixel camera (resolution 1280 x 1024

pixels) with dedicated camera button, and 8x smooth zoom

Display:

-Main: active TFT 1.8” display supports up to 262,144 colors

(128 x 160 pixels)

- External mini: 1.4” CSTN screen supports up to 65,536 colors

(96 x 65 pixels)

Bluetooth (6125/RM-178 only)
WLAN (6136/RM-106 RM-199 only)
IRDA
FM radio
Connector:

Pop-Port™ Connector

Memory Card: MicroSD

SERVICE MANUAL

Level 1&2

Environmental characteristics:

•

Lead-free soldered

Transceiver with BL-4c 820mAh Li-Ion battery pack

Talk time

Standby

Note

up to 5h

up to 11days

Depends on network

parameters

RM-106 / RM-199

Summary of Contents for 6125 RM-178











































Search results

Summary of Contents for 6125 RM-178

Reviews:

Related manuals for 6125 RM-178

Brands by name

Popular brands

Nokia 6125 RM-178, Service Manual

Search results

Summary of Contents for 6125 RM-178

Reviews:

Related manuals for 6125 RM-178

Brands by name

Popular brands