NextReef
Uncompromising Quality
TM
Other Notes:
We want you to be completely satisfied with your purchase!
The MR1 should provide years of trouble-free service if properly cared for. Here are a few
hints to help:
Your reactor may be installed anywhere, as long as the surface is flat and the reactor is
upright. Your reactor can be installed in-sump, and is also ozone safe.
When changing the media, please keep in mind that some water may leak out of the
reactor when you remove the lid. Open the reactor over a bowl, bucket, or over your
sump. New media may cloud the water in the reactor (and your tank), you may want to let
the cloudy water run off into a container to be discarded.
Rinse the reactor when changing media, including the sponges.
Replacement sponges and o-ring gaskets are available from NextReef.
Please contact NextReef or your dealer with any installation questions.
Email: [email protected] Phone: 941-704-5391 (M-F 9am – 5pm EST)
NextReef is a Registered Trademark. The NextReef stingray, stylized logo,”Uncompromising Quality”, “MR1 Media Reactor”,
and “MR1 Shorty Media Reactor” are trademarks of NextReef Systems. All designs and content copyright 2008, 2009.
LIMITED WARRANTY
NextReef makes no claim to the suitability of this product for any specific use. The end user
is solely responsible for determining fitness for a particular use, and for installation. This
product is sold as a component of a custom aquarium installation.
Your product is warranted to be free of defects for a period of 90 days from purchase. We will, at our
discretion, repair or replace your product at no charge during this period. Return shipping is the
responsibility of the purchaser. This warranty does not cover accidental damage, misuse, improper
care or alteration, or acts of God, such as floods and earthquakes. Coverage terminates if the original
purchaser sells or otherwise transfers the product. This warranty excludes claims for incidental or
consequential damages, loss of revenue or profits, loss of business, or other financial loss in
connection with the warranty problem. Some jurisdictions do not allow the exclusion or limitation of
incidental or consequential damages so the above limitation or exclusion may not apply to you. This
warranty gives you specific legal rights, and you may also have other rights, which vary from state to
state or country to country.
Problem? Question? Give us a call first – we'll be happy to help.
Thank you for choosing NextReef! Our products are hand-built in the USA, and
are designed to provide the highest level of performance for your aquatic systems.
Instructions – MR1 and MR1 Shorty Media / Substrate Reactor
Wash everything.
Plumb the MR1.
The fitting in
the center of the lid is the water inlet; the fitting offset to one side is the outlet.
Always test for siphoning
when making any change to your aquarium configuration!
While we take great care to keep any contaminates away from our
products during assembly, please take a moment to clean the reactor and plumbing before
attaching to your tank. Only clean your reactor with warm water and a single drop of plain
dish soap (avoid dish soaps with moisturizers, etc.).
Never clean Acrylic with alcohol based products.
There are multiple ways to plumb in your media reactor, depending on
your tank configuration and design – 4 are listed on the following page.
Please keep in mind that a media reactor is intended to be a bypass filter, and is not
designed to handle the complete flow and pressure requirements of a large aquarium
system. In some installations you may want to install a ball valve before the reactor – never
use one to restrict the flow out of the reactor, as this can over pressurize it.
Fittings should be wrapped with Teflon pipe tape. Do not over-tighten when installing –
should one not seal correctly, re-wrap with Teflon plumbing tape and reinstall.
The MR1 is designed to accommodate flow rates up to 160gph, and we recommend you
choose a quality pump such as the EcoPlus 132 or the Mini-Jet 606. These pumps feature
adjustable flow rates, perfect for fine tuning your reactor's performance.
Your reactor is set up to use ½ inch (inner diameter) tubing. ½ inch ID tubing will also fit
snugly around the output from an EcoPlus or Mini-Jet pump. Three plastic hose clamps are
included - the third can be used to secure tubing to the pump if you choose this installation.
If you plumb the return from your reactor into the main tank, place the return line above the
water level to avoid siphoning in the event of a power loss.
Use caution when handling as acrylic
scratches easily.
Hang On Adapter:
To install the optional Hang-On Adapter, simply loosen 4 of
the screws that secure the lid until they are flush with the
bottom of the flange. Place the HOA under the flange, align
the screw holes and tighten.
You may notice a small gap between the reactor and
the flange at some of the screws - this is normal.
You do not need to remove
the Hang-On Adapter to change the media or remove the
lid.
®
MR1/Shorty Instructions v2.0 6/09
