b
Incorrect
a
Correct
If door dimensions do not match, go to
www.nexiahome.com for drilling instructions.
2a. Check dimensions.
Install deadbolt and strike.
2
Align tailpiece of exterior keypad and interior baseplate.
3
Secure interior baseplate and install batteries.
4
Install interior cover.
5
Test lock. TEST WITH DOOR OPEN!
7
© 2013 Ingersoll Rand
Printed in U.S.A.
P516-085 01/13 c
Use the two screws shown to secure the baseplate to the door.
4a. Secure interior baseplate.
Contents
Alternate
Faceplate
AA Batteries (3)
not included
9 Volt Battery
not included
Cover
Interior
Baseplate
Strike
Baseplate
Screws (2)
Reinforcement
Plate
Reinforcement
Screws (2)
Strike
Latch/Strike
Screws (4)
Keypad
Key
Bottom Cover
Screw
Top Cover
Screw
2
³⁄₈
” (60 mm)
OR
2
³⁄₄
” (70 mm)
2
¹⁄₈
” (53 mm)
Hole
5
¹⁄₂
”
(140 mm)
The word “TOP” should be facing upward.
2d. Install bolt.
OR
2b. Check backset.
This lock will
fi
t either a 2
³⁄₈
” backset or a 2
³⁄₄
” backset. The bolt is preset to
fi
t a 2
³⁄₈
” backset. If
your backset is not 2
³⁄₈
”, you need to adjust your bolt by rotating it counterclockwise.
OR
3b. Install exterior keypad.
Bar should slide smoothly through hole in latch. If not, check door dimensions. Feed the cable over the
top of the bolt assembly then slide the tailpiece through the correct hole as shown below.
Tailpiece
IMPORTANT
Cable must slide
over latch.
Exterior
Check edge of door to determine the type of faceplate
required.
2c. If necessary, change bolt faceplate
Locate the cam on the baseplate. This cam has a small arrow on it that
should point to the arrow that is printed on the casing above the cam, like
picture “a” below. If the cam is oriented sideways, like the picture “b”,
rotate the cam until the arrows match.
3a. Check the cam on the interior baseplate.
Actual Size (2)
6b. Install the strike.
1
¹⁄₈
"
(29 mm)
2
³⁄₄
"
(70 mm)
1
¹⁄₂
"
(38 mm)
1
"
(25 mm)
¹⁄₈
" (3 mm)
Strike cut-out specifications
(not to scale)
Actual Size (2)
Actual Size (2)
1” (25
mm)
2
³⁄₄
” (70 mm)
2
³⁄₈
” (60 mm)
No change
necessary.
OR
3c. Install the interior baseplate.
Feed the cable through the hole as shown below. DO NOT connect the cable at this
time. Then slide the baseplate onto the tailpiece and press against the door. The
baseplate should stay in place.
Interior
Tailpiece
Snap the connectors together. Tuck them into the open space in the
baseplate. Make sure no wires will be pinched when the cover is installed.
4b. Connect cable.
4c. Install batteries.
1.
Unscrew battery holder.
2.
Slide out battery holder and install batteries.
3.
Attach 9 volt battery to battery connector.
4.
Place 9 volt battery in compartment.
11
22
44
33
Place the cover against the door and secure using the two screws. You may
need to rotate the thumbturn to the proper position, shown below.
Tuck wires into open space on baseplate. Be careful not to pinch any wires
between cover and baseplate.
5a. Install cover.
Install the strike.
6
Thumbturn
Actual Size
Actual Size
6a. Prepare the frame for the strike.
Mark the 4 hole locations. Drill them as shown.
If the strike cut-out has not been prepared in the frame, see the speci
fi
cations on the right.
7a. Test locking function.
Yes.
Lock is installed correctly.
7b. Test unlocking function.
2
³⁄₄
Actual Size (2)
FCC STATEMENT
This device complies with part 15 of the FCC rules. Operation is subject
to the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Changes or modi
fi
cations to this equipment not expressly approved by
Schlage could void the user’s authority to operate the equipment.
FCC ID: P2GBE369 IC: 7654A-BE369
7c. Set up your online account.
1.
Browse to www.mynexia.com.
2.
Look for “Ready to setup a Nexia™ Home Intelli-
gence system? Get started here!” and click the link.
HOME KEYPAD LOCK
INSTALLATION INSTRUCTIONS
MODEL BE369
Important Information
1
Tools Needed
• Phillips screwdriver
• Tape Measure
• Pencil
Optional
• Flathead Screwdriver
• Wood Block
• Hammer
Do not use a power
drill for installation
Place Label Here
Poner la etiqueta aquí
Placer l’autocollant ici
Default Programming Code
Código de programación predeterminado
Code du défaut programmation
Default User Codes
Códigos de usuario predeterminado
Codes du défaut utilisateur
• Lock comes preset with a default Programming Code.
• Lock comes preset with two default User Codes
(877) 288-7707
(U.S.A./Canada)
nexiahome.com
Need Help?
1. Find User Code A on the yellow sticker.
2. Enter User Code A (four digits) into the keypad.
3. Rotate thumbturn away from door edge until bolt retracts.
No.
Lock is not installed correctly.
Remove lock and reinstall. Pay close
attention to cam position in step
3a
.
1. Press
2. Rotate thumbturn towards door edge until bolt extends.
Did bolt extend?
Yes.
Lock is installed correctly.
No.
Lock is not installed correctly.
Remove lock and reinstall. Pay close
attention to cam position in step
3a
.
Did bolt retract?
Correct
Incorrect
Correct
Incorrect
3
P516-085
