HELPFUL LINKS
Visit the NetApp web site for more information.
NetApp support site
Complete AltaVault System Setup
5
Power switch
1
2
4
1
2
3
5
Visually verify that the ID for each disk shelf is unique, and if not, set the disk shelf ID.
NOTE:
A valid shelf ID for a AltaVault system could be one of 00, 01, 10, 11.
00 is the default shelf ID.
a.
Using one hand, hold the left ear cover between your thumb and index finger.
Pull either the top or the bottom of the cover until one end is released.
Pull off the left ear cover.
b.
Press and hold the shelf ID button until the first digit
on the digital display blinks.
c.
Press the button until the desired number (between 0 and 9) is displayed.
This number continues to blink.
d.
Repeat steps b and c for the second digit.
e.
Press and hold the button until the second number stops blinking.
Both numbers on the digital display should blink and
the shelf fault LED illuminates in about five seconds.
The fault LED stays lit until you power-cycle the shelf.
f.
Power-cycle the disk shelf to make the new disk shelf
ID takes effect.
g.
Replace the left ear cover.
Set the disk shelf ID
0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
480 GB
DS2246
Left ear cover
Shelf ID
digital display
(two digits)
Shelf fault LED
1
2
You must power on all the disk shelves before powering on the controller.
Powering on the controller before the disk shelf prevents AltaVault OS from operating normally.
Verify that the power supplies are working correctly:
PSU OK LED ( ) is lit green in each power supply.
View the disk shelf LEDs (on shelf front) to verify the disk
shelf powered on correctly:
Power LED ( ) is lit green.
Fault LED ( ) is not lit.
Power on disk shelf; move the power switch to the ON (|) position.
BOTH power supplies MUST be powered on.
•
•
Verify that the power supplies are working correctly:
PSU OK LED ( ) is lit green in each power supply.
View the system LEDs (on controller front) to verify the controller powered on correctly:
Power LED ( ) is lit green.
System attention LED ( ) blinks for a few minutes while AltaVault OS is booting up.
The System attention LED turns off when AltaVault OS is finished booting up.
Power on controller; move the power switch to the ON (|) position.
BOTH power supplies MUST be powered on.
•
•
Hold the bezel parallel to the front of the controller.
Install the bezel on the controller front as shown in the illustration.
The bezel will snap into place.
Install bezel
•
•
•
See the NetApp AltaVault Cloud Integrated Storage Installation and Service Guide at the NetApp Support site.
FRONT
VIEW OF
CONTROLLER
REAR
VIEW OF
CONTROLLER
Power switch
13
14
15
16
7
8
9
10
3
4
5
6
LINK
LINK
LINK
LINK
0a
0b
0c
0d
e0b
e0a
0
e0e
e0f
e0c
e0d
LINK LINK
LINK
LINK
L
N
K
a
b
c
d
X20 6 7
INT LNK
LNK ACT
LNK ACT
X31 49A
A
B
C
D
To view AltaVault documentation see:
http://mysupport.netapp.com
210-06615+A0
Installation and Setup Instructions
AltaVault System
Computer with Internet
Initial configuration is done via
serial console
Additional network cables
For connecting your storage system to
Ethernet switches
You provide:
Prepare for installation
1
4
5
1
2
3
Configuration
worksheet
Power cables:
2 per controller chassis
2 per disk shelf
SAS cables:
mini SAS HD-QSFP cable (controller-shelf)
QSFP-QSFP cable (shelf-shelf)
In the box:
Install AltaVault controller
2
4
5
1
2
3
Rack space - 10U
AltaVault system chassis: 6U
AVA10S disk shelf: 4U
Screwdriver and screws
For securing hardware into racks
You provide:
Bezel
Power LED
System
attention LED
Controller
activity LED
A
A
X2 0 6 7
X3 1 4 9A
Console port
(Setting: 9600 N-8-1)
Management port
(wrench icon)
1
3
4
e i
0
e j
0
e k
0
e i
0
3
4
2
LNK
a
0
b
0
c
0
d
0
LNK
LNK
LNK
0a
e
e0b
e0c
e0d
LNK
LNK
LNK
LNK
LNK
LNK
LNK
LNK
0e|0e
e
0f|0f
e
0g|0g
e
0h|0h
e
Controller
attention LED
|
| |
|
Power
supplies
Power on disk shelf
1
Power on controller
2
Finish AltaVault Setup over Serial Console
3
RAID Card with
mini SAS HD ports
RAID Card with
mini SAS HD ports
