![background image](http://html.mh-extra.com/html/nemco/6009/6009_operating-and-maintenance-instructions_718295001.webp)
Operating and Maintenance Instructions
Model: 6009
Infra-red Bulb Warmer Available With 2,3,4,5 or 6 Bulbs
1
INTRODUCTION
1.
Please read instructions before using this appliance.
2.
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock and
injury.
3.
Clean machine thoroughly before and after all uses following cleaning instructions below.
ELECTRICAL REQUIREMENTS
1.
Plug warmer into a grounded outlet with correct voltage and sufficient power capacity. Refer to the product label (serial plate) on
the warmer for voltage and wattage requirements.
SAFETY INSTRUCTIONS
1.
Warning!
All power must be disconnected at power source before any service procedure is performed.
2.
This appliance is hot when in use. To avoid burns, do not let bare skin touch hot surfaces. Keep combustible materials, such as
drapes and other furnishings, away from appliance.
3.
Extreme caution is necessary when any appliance is used by or near children and whenever the appliance is left unattended.
4.
Always unplug appliance when not in use and before cleaning, adjusting or maintaining this machine. To disconnect appliance,
turn controls off and remove plug from outlet.
5.
Do not operate any appliance with a damaged cord or plug, after the appliance malfunctions, has been dropped, or damaged.
Return appliance to an authorized service facility for examination, electrical or mechanical adjustment, or repair.
6.
Do not use outdoors. This appliance is not intended for use in wet or moist locations. Never locate appliance where it may fall
into water.
7.
Connect to properly grounded outlets only. Avoid the use of extension cords. Do not run cord under carpeting, runners, or the
like. Arrange cord away from traffic area and where it will not be tripped over.
8.
To prevent a possible fire, we recommend that the unit be placed on a non-combustible surface.
9.
This appliance has electrical parts. Do not use it in areas where gasoline, paint, or flammable liquids are used or stored.
PREPARATION
1.
Place warmer on TUBE STAND and tighten THUMB SCREW.
2.
NOTE: Two SCREWS must be installed in the base for UL approval. The SCREWS have been stapled to the instruction sheet.
This warmer is supplied with a UL TRAY and must be used for UL operation.
3.
Set warmer on a flat, stable surface near the power outlet.
4.
Screw BULBS into the sockets. Note: Bulbs in multi-bulb warmers should be the same (clear or red).
5.
This unit radiates heat when in use therefore we recommend that the unit be placed on a non-combustible surface.
6.
If warmer fails to work properly when first operated call NEMCO customer service at 1-800-782-6761.
OPERATION
1.
Plug warmer into a grounded outlet and turn SWITCHES on.
2.
Place food products in a pan, located directly under the BULBS for best results.
3.
Turn warmer off when not in use.
4.
Unplug the warmer before changing bulbs. To disconnect appliance, turn SWITCHES off and remove plug from outlet.
CLEANING
NOTE: Proper maintenance plays an important part in the life span and functioning of the warmer.
1.
Unplug the power cord.
2.
This warmer can be cleaned with a damp sponge and mild soap. Do not immerse in water or other liquid.
TROUBLESHOOTING
Lights not On
Check if unit is plugged in and power switches are turned to “ON” position
Check power at receptacle
Check if Bulb has blown
Loose Sockets
Turn off power and check if socket is loose or broken. Remove light bulb and tighten
socket screws as necessary.
Loose Hoods
Turn off power and check if hood is loose. Remove light bulb and tighten hood screws as
necessary.
Unit Blows Fuse or Circuit
Breaker
Check to make sure circuit is not overloaded.