background image

THANK YOU FOR CHOOSING NELLA™

Welcome to the Nella™ family. We are confident Nella’s™ superior quality, design and aesthetic will enhance your bath-

room experience for many years to come. If you have any questions regarding your Nella products please contact your 

local sales representative or visit our website www.nellabath.com for customer support and service information.
Thank you again, 

NELLA™

PRIOR TO INSTALLATION

Prior to installation please be sure to review all installation instructions with a licensed or qualified plumbing technician 

who is familiar with all local plumbing and building codes in your jurisdiction.

TOILET INSTALLATION INSTRUCTIONS

USA / Canada: 

www.nellabath.com

PRODUCT FEATURES AND DESCRIPTION 

FEATURES

• Vitreous china
• Seamless one-piece design
• 2” fully glazed trapway
• 12” (305mm) rough-In
• Siphonic Jet
• Water Conscious

TM

 Single Flush

• Low Flow 1.28 GPF / 4.8 L / HET 

INCLUDED COMPONENTS

• Seat w/lid (soft-close)
• Tank cover
• Flush actuator
• Wax ring
• Floor installation kit 

CODES AND STANDARDS

Meets or exceeds:

• ASME A112.19.2 /CSA B45.1
• ASME A112.19.14

LLYN

NBMU-2512

IMPORTANT - PRIOR TO INSTALLATION

Before you begin please be sure to review the steps below to ensure preferred installation results.
1. Unpack your new NELLA™ product and confirm it is the correct model ordered and inspect the product for damage.

Please keep product in its original packaging until you are ready for installation. 

2. Confirm that all walls are plumb and all mounting/installation surfaces are level. 

3. Shut of existing water supply. 

4. Confirm that your plumbing technician has the proper/recommended tools for proper installation.

Summary of Contents for LLYN NBMU-2512











Reviews: