INSTALLATION AND OWNER’S MANUAL
N930 or N930E (European) LIGHT BAR for
Suzuki® VS1400
PARTS LIST
Screwdriver, #2 Phillips
Socket, 10mm, and Ratchet Wrench
Pliers, Slip Joint, Hex Key 5mm
Plus tools required for removal of Upper Triple
Clamp
Description
Qty.
Lightbar Assembly, N930 or N930E
1
Connectors, Scotchlok
6
1.
Remove Headlight from Headlight Shell (Screwdriver). Set
aside.
2.
Remove nuts from Headlight Shell mounting bracket, (10mm
Socket), Lift mounting screws out of lower triple clamp.
3.
Remove back cover from Headlight Shell mounting bracket
(Screwdriver)
4.
Unplug Turnsignal Wires.
5.
Loosen clamping screws on Turnsignal mounting clamps. Pull
Turnsignal wires from Headlight Shell.
6.
Remove Upper Triple Clamp, Refer to Service Manual
7.
Slide Turnsignals up fork tubes and remove. Set aside, they
will not be reused.
8.
Reinstall Upper Triple Clamp per Service Manual.
PREPARATION
INSTALLATION
1.
Mount the Light Bar Assembly:
A.
Route the wires from the Light Bar assembly through
the lower triple clamp from below, and into the Headlight
Shell.
B.
Reinstall the back cover plate onto the Headlight
Shell mounting bracket.
C.
Hold the Light Bar assembly in place on the lower
Triple Clamp and reinstall the Headlight Shell. Tighten
the nuts manufacturer's specified torque.
2.
Wire the Light Bar Assembly:
A.
Attach the Light Bar assembly wires per the following
list;
Light Bar
Motorcycle
Turnsignal, Left
Short Red
= Light Green
Turnsignal, Right
Short Red
= Black
Running Light, Left
Short Black
= Grey
Running Light, Right
Short Black
= Grey
Passing Lamps
Long Blue
= White(Hi Beam)
Ground
= Black/White
3.
Reinstall the headlight and rim.
10-110730-000 Rev. A 03/02
NOTE:
Check local regulations for proper passing lamp opera-
tion. Some states require passing lamps be lit only with hi-beam.
NOTE:
right and left on the motorcycle are determined from the
rider’s position.
Page 1 of 2
Position light bar assembly
between the lower triple
clamp and the head light
shell mounting bracket.
Wire From Light Bar
Insert To Stop.
Through Wire
NOTE:
This installation to the VS1400 Intruder requires removal
and reinstallation of the upper Triple Clamp. Refer to your
Service Manual for the proper tools and procedure.
NOTE:
Grounding is through the frame.
NOTE:
An assistant will make steps 1 (A through C) much easier.
Note, Light Bar Wiring Helpful Hints:
The
long Blue
wire is the main power wire for the spotlights on
the light bar. Connect that to the main power source from the
headlight. Either the High Beam wire or the Low Beam wire.
The choice is your preference. Turn on bike and Check.
The two short
RED
wires are for the turn signals. One
RED
wire
for the Left side turn signal and one for the Right side turn signal.
Turn on bike and check.
The two short
BLACK
wires are for the running lights. One
BLACK
wire for the Left side running light and one for the Right
side running light. Turn on bike and check.
The Light Bar attached to the front fork of the motorcycle serves
as the ground in most cases. A precautionary step to insure
proper grounding is to take one of the Black with White Tracer
Ground wires from the existing turn signals and ground that
between the Light Bar Mount and the Triple Tree Bracket.
Always start by doing one side at a time. Preferably the right
side or high side of the bike first.
NOTE:
check vertical aim of the lamps. They should
aim approximately 5° downward. If adjustment is
required see “Adjustment” page 2 of this instruction
otherwise proceed with wiring step 2.
