![background image](http://html.mh-extra.com/html/nakanishi/em-4020/em-4020_operation-manual_704420001.webp)
CAUTION
WARNING
EM-4020
・
EM-4020A
EM-4040
・
EM-4040A
OPERATION MANUAL
Brushless Motor
Thank you for purchasing the EM-4020
・
EM-4020A
・
EM-4040
・
EM-4040A Brushless Motor. The <E4000
CONTROLLER>, <E4000 Series Spindle>, and <Air Line Kit > are required to drive this brushless motor. Read
these Operation Manual carefully before use. Also read <E4000 CONTROLLER>, <E4000 Series Spindle>, and
<Air Line Kit> Operation Manuals. Always keep this Operation Manual in a place where a user can referred to for
reference at any time.
1
. CAUTIONS FOR HANDLING AND OPERATION
■
Read these warnings and cautions carefully and only use in the manner intended.
■
These warnings and cautions are intended to avoid potential hazards that could result in personal injury to the
operator or damage to the device. These are classified as follows in accordance with the seriousness of the risk.
Class
Degree of Risk
WARNING
A safety hazard could result in bodily injury or damage to the device if
the safety instructions are not properly followed.
CAUTION
A hazard that could result in light or moderate bodily injury or damage
to the device if the safety instructions are not followed
①
This brushless motor is not a hand tool. It is designed to be used on CNC machines or special
purpose machines.
②
Do not touch the cutting tool while it is running. It is very dangerous.
③
Wear safety glasses, dust mask and use a protective cover around the spindle whenever the
spindle is rotating.
④
Never connect, disconnect or touch the Connector and Motor Cord Plug with wet hands. This
may cause an electric shock.
⑤
Never operate or handle the brushless motor until you have thoroughly read the Operation
Manuals and safe operation has been confirmed.
1) To prevent injuries / damages, check the spindle and cutting tool for proper installation,
before operating the brushless motor.
2) Before disconnecting the brushless motor, always turn the control power off and turn the
compressed air supply to the CONTROLLER off. Then it is safe to remove the brushless
motor.
⑥
When installing a brushless motor to a fixed base, make sure the fixed base is grounded in
order to avoid the risk of an electric shock.
①
Do not drop or hit this brushless motor, as shock can damage to the internal components.
②
Select suitable products or tools for all applications. Do not exceed the capabilities of the
spindle or tools.
③
Carefully direct coolant spray to the tool. Do not spray directly on the brushless motor body.
④
Stop working immediately when abnormal rotation or unusual vibration are observed.
Afterwards, please check the content of section 7 "TROUBLESHOOTING".
⑤
After installation, repair, initial operation, or long periods of non operation, please carry out
break -in as follow. Start rotating slowly and over a short period of time, increase speed
gradually until allowable maximum speed.
⑥
Do not disassemble, modify or attempt to repair this brushless motor. Additional damage
will occur to the internal components. Service must be performed by NSK NAKANISHI or an
authorized service center.
⑦
When using this brushless motor for mass production, please purchase the another brushless
motor as a spare in case of an emergency.
2
. FEATURES
①
The Brushless Motor housing is made from precision ground, hardened, stainless steel (SUS) with an outside
diameter of
ȭ
40 mm.
②
Excellent durability and high reliability are obtained by using a high-speed brushless motor, which eliminates
the need for brush replacement and frequent maintenance.
③
The maximum output is 1200W.
④
A quick disconnect cord is available for easy brushless motor removal.
⑤
Air-cooling system with a small volume of air (100
ℓ
/ min) is used to prevent heat buildup and allows long
continuous operation.
OM-K0644E
3
. SPECIFICATIONS AND DIMENSIONS
3 - 1 Specifications
Standard Accessories
・
Wrench (36mm)
・・
1pc.
・
Operation Manual
・・
1set.
3 - 2 Outside View
Fig. 1
3 - 3 Torque Characteristics
Model
EM-4020
EM-4020A
EM-4040
EM-4040A
Maximum Rotation Speed
20,000min
-1
40,000min
-1
Max. Output
1,200W
Weight
1,300g
1,800g
1,300g
1,800g
*Note1 :
Motor Cord is sold separately. Please select the suitable motor cord length for your application.
<Option>
Motor Cord
*Note1
EMCD-4000-
□
M
(Power Line)
Cord Length : 2m, 4m, 6m, 8m
(The Air Hose (
ȭ
6mm) of the same length is attached.)
EMCD-4000S-
□
M
(Signal Line)
Cord Length : 2m, 4m, 6m, 8m
(The Air Hose (
ȭ
6mm) of the same length is attached.)
These Motor Cords <EMCD-4000-8M and EMCD-4000S-8M> are never to be usd for Angle
Type Brushless Motors <EM-4020A and EM-4040A>. 8 Meter Cords cannot be used on "A"
Type (90-Degree) Motors.
Fig. 2
①
EM-4020
・
EM-4040
②
EM-4020A
・
EM-4040A
Fig. 3
Fig. 4
①
EM-4020
・
EM-4020A
②
EM-4040
・
EM-4040A
CAUTION
ȭ
40
0 -0.01
(
300
)
172.8
(
14.4
)
ȭ
40
0 -0.01
(
2,000
)
(
14.4
)
195.2
0
5
10
15
20
1400
1200
1000
800
600
400
200
0
100
90
80
70
60
50
40
30
20
10
0
Continuous Duty Area
Speed (
x
10
3
min
-1
)
Output
(W)
Torque
(cN
・
m)
Output
Torque
0
5
10
15
20
25
30
35
40
1400
1200
1000
800
600
400
200
0
100
90
80
70
60
50
40
30
20
10
0
Speed (
x
10
3
min
-1
)
Output
(W)
Torque
(cN
・
m)
Continuous Duty Area
Output
Torque