background image

OptimAir

®

MM 2K

Mask-Mounted

Powered Air-Purifying Respirator

USER

S INSTRUCTIONS

The warranties made by MSA with respect to the product are
voided if the product is not installed, used, and serviced in
accordance with the instructions in this manual. We encourage our
customers to write or call for a demonstration of this equipment
prior to use or for any additional information relative to use or
repairs. Call 1-800-MSA-2222 during regular working hours.

See Approval Matrix Part No. 818105 for NIOSH Approvals and
Limitations.

THIS MANUAL, INCLUDING THE WARNINGS AND CAUTIONS
INSIDE, MUST BE READ AND FOLLOWED CAREFULLY BY ALL PER-
SONS WHO USE OR MAINTAIN THIS PRODUCT, INCLUDING THOSE
WHO HAVE ANY RESPONSIBILITY INVOLVING ITS SELECTION,
APPLICATION, SERVICE, OR REPAIR. THIS RESPIRATOR WILL PER-
FORM AS DESIGNED ONLY IF USED AND MAINTAINED ACCORD-
ING TO THE INSTRUCTIONS. OTHERWISE IT COULD FAIL TO PER-
FORM AS DESIGNED AND PERSONS WHO RELY ON THIS PRODUCT
COULD SUSTAIN SERIOUS PERSONAL INJURY OR DEATH.

TAL 0110 (L) Rev. 8

© MSA 2010

Prnt. Spec. 10000005389(F)

Mat. 10020949

Doc. 10000007610

Summary of Contents for OptimAir MM 2K

































Reviews: