background image

 

installation and service manual

oil-fired unit heaters

model Por

models manufactured after september 2007 with Beckett clean cut Burner

4-522.4

5H75804 rev.d

inspection on arrival

1.  Inspect unit upon arrival. In case of damage, report 

immediately to transportation company and you local Modine 
sales representative.

2.  Check rating plate on unit and motor to verify that power 

supply and motor specification requirements meet available 
electric power at the point of installation.

3.  Inspect unit received for conformance with description of 

product ordered (including specifications where applicable).

September, 2007

THIS MANUAL IS THE PROPERTY OF THE OWNER. 

PLEASE BE SURE TO LEAVE IT WITH THE OWNER WHEN YOU LEAVE THE JOB. 

 

WARNING

improper installation, adjustment, 
alteration, service or maintenance can 
cause property damage, injury or death, 
and could cause exposure to substances 
which have been determined by various 
state agencies to cause cancer, birth 
defects or other reproductive harm. read 
the installation, operating and maintenance 
instructions thoroughly before installing or 
servicing this equipment.

FOR YOUR SAFETY

WHat to do if you smell gas:

1. open windows.
2. do not try to light any appliance.
3. do not touch any electrical switch; do   
  not use any phone in your building.
4. immediately call your gas supplier. 

 CAUTION

to prevent premature heat exchanger 
failure do not locate any oil-fired units in 
areas where chlorinated, halogenated or 
acid vapors are present in the atmosphere.

FOR YOUR SAFETY

the use and storage of gasoline or other 
flammable vapors and liquids in open 
containers in the vicinity of this appliance 
is hazardous.

IMPORTANT

the use of this manual is specifically 
intended for a qualified installation and 
service agency.  all installation and service 
of these units must be performed by a 
qualified installation and service agency.

Содержание POR





















Отзывы: